RK38G2J4 Hotpoint Range - Instructions

With great ease. Only thing I would have appreciated was knowing the size ofvthevrequired socket wrench. Otherwise it was easy and fun as the instructions were crystal clear.

Could not believe how fast the part shipped. 2 days and it was here. All it took was using a nut driver to remove 4 screws and then put the new one in.

My 17 year old son and I (his mom) replaced the oven element in less than 15 minutes!!! It was so easy. We first unplugged the stove since I didn't want to go and shut off the circuit breaker in the dark!! We then removed the two screws that hold the element in place and started to pulled out the element. It was actually corroding in my hands as I pulled it out. We disconnected the wires and then put in the new element by reconnecting the wires, pushing the connections back in and replacing the two screws that hold the element in. The oven heated right up!!! What a savings to do it yourself and not have a repairman charge us extra to do a 10 minute job!! Thank you Part Select for your fast service. I will definitely look here before I shop anywhere else. Thanks,

Four screws and two wires.

No. 1 thing I did is I unplugged power supply to oven, second- unscrewed two screws that was holding cover plate and removed cover plate with a set of pliers, pulled element out and unscrewed two screw with power wires and installed new element, tightened screws and re-installed cover plate, tested oven turning on oven and in a few seconds element got hot, job done!

First I turned off the breaker to the oven,
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the oven on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

every thing went just fine. A simple job at best.

What went better was the prompt service.

Thanks

Element was easy to remove two screws and unplug it. New element didn't have the same prongs and brace was different. Added ends to plug with screws supplied drilled new holes in oven back for brace. Works fine for a repair by a 65 year old woman.

Unplugged oven. Removed the two screws from inside the oven that secured element to the back. I then removed the protective cover for the plug from behind the oven-three screws. Disconnected the element from the electrical wires, removed and replaced the element. And reassembled the cover and all the screws in reverse order. Plugged it in. Presto, 5 mins and works great.

My daughter and I turned off the breaker to the range and removed the old element and replaced it with the new one. My husband came home and took over after we had done almost everything ourselves!!

My husband removed the screws holding the element, disconnected the wires from the old element. He then reattached the wires to the new element, putting it back into place, tightened the screws, and we were cooking again. The shipping service was GREAT! I ordered the part on-line and it arrived next day! Thanks!

I removed the original element with socket set (two hex nuts). I removed the element and face plate, reversing the steps when installing the new element. It was simple.

I noticed two screws held the heating element in place. I removed the screws. Pulled the heating element out a few inches. Removed the two additional screws which held the two wires on.

To install the new element, I used the two new screws that came with the element to attach the wires to the element. Insert the element into position and attached the element to the rear wall with the two screws which were first removed.

turned off the electric at the breaker box.
removed the door, and racks. unscrewed two bolts, pulled out and unscrewed the leads. reattached the leads, and pushed in and reattached the element.
put the racks and door back on. turned on the electric and then tested the oven. easy!!