RB757GN1KK Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roderick from Pleasanton, CA
- Parts Used:
- WB14X104
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic roller on hinge had broken causing door not to open easily
Slid door off hinges. Removed 3 screws which hold hinge in place. Removed drawer to access spring for hinge. Gasped at all the crumbs and crap which had collected underneath the drawer. Cleaned up crumbs+crap from floor. Disconnected spring from hinge and removed old hinge completely. Installed new hinge with 3 screws. Attached spring to hinge - center hole fitting. Slid drawer back in place. Angled hinges outward in order to re-install door. Slid door back onto hinges. Door now operates nice and smoothly. Job well done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Northridge, CA
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic roller on right hinge was broken
Pulled oven door up and off. Removed old hinge and installed new hinge. Replaced oven door. It was a very simple job. The whole project took less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alexis from Birch Run, MI
- Parts Used:
- WB3X5699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
timer and cleaning timer knobs broken
two of the knobs pushed on perfectly,
Other than that they came quickly and I loved the service.
Thank you
Other than that they came quickly and I loved the service.
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tami from Mount Vernon, WA
- Parts Used:
- WB14X104
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven door was not opening all the way
The plastic wheel glide that the hinge runs back and forth on was worn off on one side so it was grinding and binding.
Remove storage drawer from under oven. Open the door to the special catch position and carefully lift door off the hinges - (not by the handle, hold onto both sides).
Take out three screws w/ a hex head nut driver, slip the hinge down into the hole, look under drawer area w/ flashlight and carefully unhook spring, while holding onto spring- pull old hinge out, see which hole has wear (that's the one you want to use of the three), insert new hinge all the way in and hook up spring. Pull hinge out and line up front plate w/ holes, insert 3 screws snugly. Done, awesome probably saved a 200.00 visit from the appliance guy. My husband thinks I'm amazing!
Remove storage drawer from under oven. Open the door to the special catch position and carefully lift door off the hinges - (not by the handle, hold onto both sides).
Take out three screws w/ a hex head nut driver, slip the hinge down into the hole, look under drawer area w/ flashlight and carefully unhook spring, while holding onto spring- pull old hinge out, see which hole has wear (that's the one you want to use of the three), insert new hinge all the way in and hook up spring. Pull hinge out and line up front plate w/ holes, insert 3 screws snugly. Done, awesome probably saved a 200.00 visit from the appliance guy. My husband thinks I'm amazing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Saint Petersburg, FL
- Parts Used:
- WB14X104
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The right hinge was broken and the door would not close properly.
I removed the door by pulling up and away from the hinges. I then removed the drawer. I unhooked the tension spring by hand and noted the opening. I then removed the three screws on the hinge assembly, removed the ole part, and replaced it with the new one. I replaced the tension spring and slid the door back on to the hinges. I did it all in less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLARD from GLOVERSVILLE, NY
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
instructions could be better
it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Austin, TX
- Parts Used:
- WB3X5699
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Only able to get 1 little knob on
You are supposed to be able to just pop them on. Got one on the two others will not go on.
Help!
Help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Nashville, AR
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
R had ight front control made loud noise when contacts opened.
This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from New smyrna beach, FL
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Burner constantly heated
Good directions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Baden, PA
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Front Burner,no control of.
The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Hamilton, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Shaft for burner control knob broke off
I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Yardley, PA
- Parts Used:
- WB44X232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
The broiler element burned out and needed replacement.
1. Put the breaker for the stove on the the OFF position. 2. Remove the two hex screws with robo grips, 3. Gently pulled the element outward. 4. Disconnected the broiler element. 5. Connected the new element. 6. Gently pushed the new element back in place. 7. Replaced the hex screws. 8. Put the breaker back to the ON position. DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Waukesha, WI
- Parts Used:
- WB2X9146
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drawer coming out of the track and falling to the floor.
pulled drawer out and installed drawer guide
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Winter, WI
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!