RB757GN1KK Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from PLANO, TX
- Parts Used:
- WB21X36771
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Old infinite switch WB21X36771 broke...heating element stopped heating
1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hedgesville, WV
- Parts Used:
- WB2X9719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element clap broke off
All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Kernersville, NC
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven door hinge roller deteriorated, oven door hard to open.
Open and slide door upward off of hinges. Removed bottom drawer to access hinge spring. Detached spring, noting proper hole in hinge for reinstallation. Removed three screws holding hinge and removed hinge. Compared new part to old...exact match. Inserted hinge, and reinstalled the three screws. Reattached spring in hinge hole. Slid door back down onto hinges. Done in four minutes flat!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SONORA, CA
- Parts Used:
- WB3X5699
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
missing knobs on clock and timers
Installed new knobs, mom is happy!!
Was this instruction helpful to you?
Thank you for voting!
oven door jammed,could not open it
Removed old hinges and installed new hinges.
Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they sold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.
Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they sold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.
Was this instruction helpful to you?
Thank you for voting!
Broiler element would not work.
Removed the old element: removed clips holding the element, unscrewed the 2 screws that hold element in place. On the back of the range, removed casing to get to the connection wires, disconnected the element then removed the element. Reversed procedure to replace. Thanks for the speedy ordering and delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- octavio from lake worth, FL
- Parts Used:
- WB44X232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
broil unit caught fire and burned all the way around it
My great and talented hubby did it. He can fix anything. It was easy for him.
I love this website to purchase parts. Both times I have ordered something from you, it has been at a reasonable price and I received it really quickly.
Thanks!
I love this website to purchase parts. Both times I have ordered something from you, it has been at a reasonable price and I received it really quickly.
Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Young from Oakland, NJ
- Parts Used:
- WB44X232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
broken heat element
It was very easy than i expect,
Just pullout the stove from the location to access rear side of stove,
unscrew 3 nuts with socket rench and disconnected wire. Opened front door of stove, unscrew 5 screwss , then pulled out broken element, replaced it with new one.
It is very very easy , Dont be affraid do it yourself.....
Just pullout the stove from the location to access rear side of stove,
unscrew 3 nuts with socket rench and disconnected wire. Opened front door of stove, unscrew 5 screwss , then pulled out broken element, replaced it with new one.
It is very very easy , Dont be affraid do it yourself.....
Was this instruction helpful to you?
Thank you for voting!
Hinge design is weak: Hinge roller wheel splits; it's been replaced twice in last two years
1. Slide oven door off hinge arms and set aside
2. Slide out oven bottom drawer and set aside
3. Detach springs from perforations in stove rails then hinges and set aside
4. Loosen three screws in each hinge, remove and set aside.
5. Remove hinges, threading them out through openings
6. Thread new hinges into stove openings. Align hinge arms with hinge wheels.
7. Align and tighten three hinge screws in each hinge.
8. Re-attach springs to perforations in hinge, then stove rails
9. Slide oven drawer into stove and door into hinge arms
2. Slide out oven bottom drawer and set aside
3. Detach springs from perforations in stove rails then hinges and set aside
4. Loosen three screws in each hinge, remove and set aside.
5. Remove hinges, threading them out through openings
6. Thread new hinges into stove openings. Align hinge arms with hinge wheels.
7. Align and tighten three hinge screws in each hinge.
8. Re-attach springs to perforations in hinge, then stove rails
9. Slide oven drawer into stove and door into hinge arms
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Hindman, KY
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner wouldn't operate
Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel
Knott County Housing Authority Maintenance Personnel
Was this instruction helpful to you?
Thank you for voting!
The right side hinge roller broke making the door balky
Lifted the door off the hinges, unhooked the spring from each hinge, unscrewed 3 Phillips head screws from the face plate of each hinge and removed the hinge assemblies . Hinges went in the way they came out; easy shmeasy. Took less than 15 minutes and the door is like new.
Was this instruction helpful to you?
Thank you for voting!
Oven door would not stay open.
Called in and talked to someone and he look yup what he thought was correct but after i got them theywere wrong so i sent them back for a full refund minus 9.90 freight. I still need to figure out what i need for my 27 inch wall oven. Please help. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angelo from STATEN ISLAND, NY
- Parts Used:
- WB14X103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
left hinge wheel cracked
REMOVED DOOR TO OVEN
REMOVED HINGE [3 SCREWS]
REMOVED BOTTOM DRAW
UNHOOKED SPRING FROM LEFT SIDE ATTACHED TO HINGE
PULL OUT DEFECTIVE HINGE
REPLACE WITH NEW HINGE AND SCREWS
REHOOK SPRING TO HINGE & REPLACE DOOR
COMPLETE
FOLLOW VIDEO PROVIDED BY PARTS SELECT
REMOVED HINGE [3 SCREWS]
REMOVED BOTTOM DRAW
UNHOOKED SPRING FROM LEFT SIDE ATTACHED TO HINGE
PULL OUT DEFECTIVE HINGE
REPLACE WITH NEW HINGE AND SCREWS
REHOOK SPRING TO HINGE & REPLACE DOOR
COMPLETE
FOLLOW VIDEO PROVIDED BY PARTS SELECT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christy from Danville, CA
- Parts Used:
- WB3X5699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
timer knobs broken off
I simply took the 3 new timer knobs and slid them on the metal shafts. It took less than 5 minutes to replace all 3 knobs. Now I can set the start, stop and time functions which have been inoperable for over 5 years. An easy and straight forward .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeNise from FT WASHINGTON, MD
- Parts Used:
- WB3X5699
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Knobs were broken.
Removed old knobs and inserted new ones.
Was this instruction helpful to you?
Thank you for voting!