RB757GN1KK Hotpoint Range - Instructions

First I removed the door by lifting it off the hinge assemblies.

Then I removed the drawer to access the spring.

Removed the spring, noting which attachment hole was used.

Removed the hinge assembly with a Phillips screwdriver.

Replacef the unit.

Repeated for the other hinge assembly.

Note: it took longer to find the correct parts in the parts diagrams than it did to replace them.

1. Removed the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.

Before removing screws, I reached in and felt for where the upper end of the spring attached to the hinge. There are three holes in the end of the hinge arm, so I wanted to be sure of which hole to use. (The holes are very close together, so if the spring falls out before you determine which hole it was in, it probably won't matter so long as you are sure to use the same hole on both new hinges.) I then removed three Phillips screws per hinge. Once the hinge was loose, I could wiggle it around and release enough of the spring tension to slip the top end of the spring out of the hole on the hinge arm. Then I pulled out the old hinge and inserted the new one and replaced the three screws. Without the tension, the lower end of the spring fell out of the little hole in the oven bottom where it normally attaches. Our gas oven has a broiler rather than a storage drawer, so it was a little difficult to get the lower tip of the spring back into that hole. It actually ended up being easier to get the lower tip of the spring back into that hole first, before trying to reattach it to the hinge arm. Once I got the lower end into that hole, I pulled up on the spring and maintained upward pressure on the spring while I fiddled around to get the upper end into the hinge arm hole. Took about 20 minutes, door works perfectly now. Lots of sharp edges inside the oven, so had to be careful.

Pull oven door open about a couple of inches. Grab the door by the sides and pull up to remove from the hinges. Set it aside. Remove the storage drawer under the oven. This gives you access to the tension spring attached to the hinge. Detach it by hand. Using a phillips head, unscrew and remove the damaged hinge. Replace the new hinge. Reattach the spring. Replace the storage drawer. Replace the oven door. Done.

scissors and opened bag. determined that all three knobs were identical. aligned slots on each knob with flanges on each shaft.
snapped each knob into place.
Did a happy dance of empowerment around the kitchen. ( knobs had been broken for at least 5 years).
used timer to avoid burning christmas cookies.
Have a Merry one!!!

Snapped in the clip

Ever the optimist, I'd replaced the burner on this relic of another time to no effect. That left the switch. You guys should know that when a burner element goes bad it can take out the switch. I should have put a meter on it. Wehn I looked for a replacement a few months ago there were still factory parts available, but they were $80 or so and I wasn't inclined to risk that on a 40 year old range. I offered to replace the raange for my daughter as a Christmas present but she like this old thing. It was an unusual size with a pan storage compartment on the left. I went on line and found this universal replacement for about $25 delivered. What the heck. I ordered it and it arrived within a week. I pulled the stove out, killed the breaker, pulled the knob off, used a nut driver to take ther rear panel off, two phillips screws under the knob hold the switch in. The terminals on the old switch are in a slightly different order but are clearly marked L1, L2, H1, H2 and P. The P is the power and has a smaller terminal so you can't put it on the wrong one. Just examine the old switch ( it was marked the same way) take off the L1 and put in on the L1 of the new switch and so on, make sure you use the correct knob adapter to fit your old knob and break the switch stem to the correct length. It will break easilly if you hold it with one pliers and break it with another. Screw the new switch in place with he old screws. At this point, I closed the breakers and tested it. It worked fine. I turned the breakers off again. Buttoned it up and slid the stove back into place. 20 minutes tops. Great product. Good for another forty years.

Simply inserted the clip into the hole in the oven. It took less than 20 seconds. :D

I used a socket set to remove broiler element. It was stiff after so many years, but no problem. All was going well until I pulled too hard on the old element(I'd recommend jiggling if stuck, not yanking) & 1 of the 2 connectors pulled loose & fell behind the back. After my initial panic, I summoned my courage, unscrewed the coverings in the upper back of the stove, found the lost connection, pushed the new element ends through the holes from inside the oven (easiest way to hook it up at this point), plugged it in from the back, pushed it back thru into place inside the oven, reattached everything (front & back), & it worked PERFECTLY! Had I not made a mess of it, it would have taken approx. 5-10 minutes. As it was, it took approx. 15 minutes. EASY!

Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]

pushed on the new knobs.
thanks fore having the parts.

I could not believe how easy it was to repair my own oven! Honestly I was shocked. I pulled the oven out, unscrewed 7 screws, pulled the old element out, placed the new one in, replaced the screws and I was done. All I could think about was how much money I saved! Also, it took me about 15 minutes.

I ordered the replacement clips from this site and they arrived in a timely manner. The clips were perfect, but due to the age of the oven, the holes had elongated and the new clips kept falling out also. I modified the clips by widening the tips with a pair of pliers. They are holding just fine. I don't think the older clips could've withstood the modification.

All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.

New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!