RB767GN1KK Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Winter, WI
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Yardley, PA
- Parts Used:
- WB44X232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
The broiler element burned out and needed replacement.
1. Put the breaker for the stove on the the OFF position. 2. Remove the two hex screws with robo grips, 3. Gently pulled the element outward. 4. Disconnected the broiler element. 5. Connected the new element. 6. Gently pushed the new element back in place. 7. Replaced the hex screws. 8. Put the breaker back to the ON position. DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Waukesha, WI
- Parts Used:
- WB2X9146
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drawer coming out of the track and falling to the floor.
pulled drawer out and installed drawer guide
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Huron, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from bristol, CT
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Door would not open all the way
Well after fighting with the door for a month, i went on this site and using their information, i found the model number (in the process i found the receipt for the oven and found out it was 20 years old still looks and works like new. Pulled the door up and off the hinges, removed the drawer, saw the spring was in the middle hole, removed three screws pulled out old hinge. Installed new hinge, 3 screws and the spring. put the door back on and wow it worked! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Denhim Springs, LA
- Parts Used:
- WB14X103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hinge on oven door had a broken pulley.
Very easy job. Removed the 3 screws from the oven body, and slid the hinge out of the door. Slid in the new hinge, replaced the screws, and it was done. Very easy, wish I had done it sooner. Finding the part was easy, using the parts diagram. Rep was nice and confirmed the right part. Shipping was fast, and price was reasonable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Northport, NY
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
hinge became bent - door unable to open or close properly
The video accompanying the part was very beneficial, making the repair easy and quick. Your online site was concise and organized. The product was easily identified and ordering was clear and secure. From a person with no ability to fix anything, thank you for helping to solve a problem in an manageable and comfortable way. A very satisfied customer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Richmond, VA
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken roller in hinge
Slipped off the front door. Removed 3 screws & spring. Replaced with new part. Hooked the spring & secured with the three screws.
Was this instruction helpful to you?
Thank you for voting!
Oven door hinge wheels were worn out and grinding.
Followed the online video. Unhooked the springs, removed the 3-screws on each side. Installed the new hinges in reverse order. Used the wear marks on the old springs to ID and place the new springs in the holes on the new hinges. Great company to deal with....never a surprise, Great communications letting you know that your parts were on order and then again that they were shipped with shipping info and numbers to call with any questions. The best part has been that the parts drop right in everytime I have ordered from them!!!! Thanks Dan!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from North Windham, CT
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Plastic roller broken
Smooth and quick. Fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Sandy Hook, CT
- Parts Used:
- WB14X103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Range door was hard to open and would not close completely
I watched the video in the website and in less then 5 minutes replaced the broken hinge with the new one and the door works perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Montoursville, PA
- Parts Used:
- WB17X210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Right Front [surface burner terminal block kit]
We did the repair by following the inclosed instructions. we are elderly retired average ages 82. This was our first repair and it went very well. We are so pleased to have saved over $80.00 compared with hired labor 3 yre. ago for the same part. Thanks so much for your good service.
Was this instruction helpful to you?
Thank you for voting!
one oven hinge broken
It took longer to watch the video on how to replace the hinges than it did to replace them. Simple and easy. Video knocked it out of the park for ease. And now the oven door works great! thanks!!!! Video suggested if you're replacing one side do both, couldn't agree more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Black River Falls, WI
- Parts Used:
- WB14X103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The left hinge broke
It was really easy, and my only problem was getting the 3 screws out. I just used some WD40 and liquid wrench to free up the screws. After those were out I was in BUSINESS!!! I then just screwed in the 3 screws, and used my needle nose pliers to reattach the spring and WA-LAH!!! Done deal.
Was this instruction helpful to you?
Thank you for voting!