RB757WB1 Hotpoint Range - Instructions

Simply slide stove away from wall and unplug. Remove the center back plate on the rear of the stove, Open oven slide new element into rear of oven, snap into place. Return to rear of oven. slide wire connectors onto oven element prongs, replace center cover, make sure oven is turned off, plug stove back in and slide back into place. Open oven and turn on. allow element to heat up. Once the element has heated and the new burns off. Turn off the oven and replace the racks, This entire process took maybe 5 minutes.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Ordered new parts. Received email with tracking number. Parts arrived as promised. Turned off power at breaker (!). Removed burners and pans. Lifted the lid of the range. Inspected the plugs and discovered one had come loose from bracket and was not in straight. Reset plug in bracket. While the lid was open, placed the drip bowl in opening and installed the burner and made sure the burner was laying properly in the drip bowl. Repeat for each. Perfect fit, If done properly, the small burners should lay down flat and not rock back and forth. I have seen complaints about rocking, and experienced some of it on one burner. Make sure the heating element is set in the plug well and it should work. A little patience may be required to get it just right. Everything lays flat and the stove looks new again. I have purchased from Part Select on other projects including a dryer rebuild and a new face plate for this range. Great products, reasonable prices, wonderful tutorial videos and good service.

The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

Good directions

Required new light lens for oven this type has five (5) of them; only the oven temp light lens was damaged. Ordered from Parts Select.com received item fast in seven days. removed rear guard plate, than oven temperture switch than slid the neon light switch off of the light lens.Lens is removed from the front panel. Installation is reverse order.

Unplug the old one and plug in the new one. Nice and easy.

Removed the 2 screws, unpluged the 2 wires and installed the new elment

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

The only problem was m short arm and no good flash lights around

Remove center cover on back of stove exposing wiring. Unplug stove from 220v outlet. Unplug wires from old element.From inside stove, Remove 4,quarter inch screws holding back panel inside oven in place. Remove back panel from inside oven. Will be able to see the brackett on element and 2 screws holding the element/brackett in place, remove those 2 screws and remove old element. Reverse process to install new element.

My husband was able to easily remove and replace the switch and know with-in 15 minutes.