RB737G*D1 Hotpoint Range - Instructions

The only hard part of the job is removing the old, corroded terminal block. Be careful not to break the electrical wire. Other than that, just sand the contacts and reassemble. This is the second one I have replace on my 4 burner stove. 2 more to go.

First off the part was easy to find on Partselect...

Second point... ordering was easy and shippment was fast thanks to Partselect...

Replacezment was fairly easy useing a Nut driver and a pair of pliers...took about 40 minutes.

Thank you Partselect...

Chuck

Open oven door about 3 inches - then holding on the door on either side - pull up and door slides off - put it aside - this is to make it easy for you to work inside oven compartment - at rear of oven where the element goes into the back wall - there are two nuts to remove - I did not have a nut drive so used a pliers (GE could have put slots in the nuts so one would just need a screwdriver) - pull element forward - there are wires attached to the 2 ends of the element - remove with screw driver - element is off - get new part from PartSelect -(and must say pleased with their service) - and reverse above procedure.

Shut off power, Removed and disconnected element, connected and mounted new element!

I had begged my husband for 1 1/2 years to fix the oven and he said it would be cheaper to buy a new one but he wouldn't go buy one. So I decided to fix it myself. I removed the screws that hold the element and then I pulled the element out and disconnected the wires. I then hooked the wires to the new element and pushed it back in place and attached the two screws. I made sure to put the insulation back in place and now I can cook cornbread again! Thank you so much for making this so easy for me to do by myself.

1)Unscrewed the mounting nuts, 2) pulled the heating element out a couple of inches, 3) unscrewed the screws holding the wires in place, 4) removed and tossed the old heating element, 5) placed the new heating element in place, 6) re-screwed the wires to to the element, 7) pushed the heating element back into the wall of the oven, 8) reset the mounting nuts, 9) cleaned up the work area, 10) cranked up the oven and made a pizza. I'm not particularly skilled when it comes to things of this nature, but it was ridiculously easy...

All other reviews decribed the repare process that I used with no problems. The only reason I took about twenty minutes instead of around 15 minutes was it took me a few minutes to get the correct socket to remove the two small lag screws of the old bake element to free it from the oven wall. I did not have to remove the oven door as it was not a problem in reaching the back of the oven. My range is 25 years old.

The part was very easy to locate on the website. The shipping was very fast and the part was easy to install!

Unplugged oven, removed 2 screws that hold the element in place. Pulled element to expose wires. Disconnected wires & removed old element. Reversed removal for installation, plugged in and worked great.

I first remove the oven door, which is very east on this model. You tilt it a quarter of the way when you open it to use and pull up. It comes off very easy. My second step was pulling on the bake element towards the front. It will expose the wiring connection to the bake element. You will see two wire that are attached by two one screw for each connection. You will need a nut driver to remove. The removal is very simple. Note: Please be sure to turn off your circuit breaker to the oven! ( this is a safety measure,plus it will make you more at ease with the installation. You then can remove the screw nuts & replace with you new bake element. A real piece of cake & very easy even for a average home-owner. Thanks to Part Select for ease of ordering this item. It is a very friendly website! Thanks! Orin

First I removed the 2 screws holding the element in place then pulled the element out a few inches.
I removed the 2 screws that connected the wires to the element and removed old element from oven. The new element was placed in the oven and connected by reversing the steps just described. New element works perfectly!

I removed the old element after turning off the breaker to the oven. Remove the two screws that hold it to the back wall of the oven, slid it towards me exposing the wire connection. Removed the screws from the wires and removed the old element. Cleaned the oven and installed the new element by reversing the steps I just talked about. Quick and easy, oven has never worked better.

Unscrewed the two screws that held it in place; disconnected the old; connected the new; replaced the screws. DONE.

First I turned the power off to the oven at the breaker box. Then I removed the nuts holding the element to the rear wall of the oven and pulled it out a couple of inches. I saw that only 2 nuts held the element to the wires. I found the part on your site very easily and placed my order. The part was at my door 2 days later! I removed the old element, replaced the new element and turned the breakers back on. Repair complete!

I made sure the power was off. I removed two screws from the mounting plate, then I pulled the heating element forward two inches. Where the wires were attached by two screws, I removed those screws also; the heating element was freed up. I then removed it and replaced the 28 year old heating element with a brand new one.