RB737G*D1 Hotpoint Range - Instructions

No. 1 thing I did is I unplugged power supply to oven, second- unscrewed two screws that was holding cover plate and removed cover plate with a set of pliers, pulled element out and unscrewed two screw with power wires and installed new element, tightened screws and re-installed cover plate, tested oven turning on oven and in a few seconds element got hot, job done!

First I turned off the breaker to the oven,
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the oven on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.

Removed old terminal block by removing one mounting screw. Removed two wires from block. Installed new terminal block by reversing procedure.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

I removed the burner, then the chrome dish. The nuts for the wires were rusted to the terminals, so I had to break the module apart and grind the nuts off.After that the new module went fine.

Turned off circuit. Unscrewed old element. Connected new element and screwed it in. Worked like a charm. It shipped very quickly. Could not be more satisfied; total repair: $30 and prevented me from buying a new oven; satisfaction: priceless.

Element was easy to remove two screws and unplug it. New element didn't have the same prongs and brace was different. Added ends to plug with screws supplied drilled new holes in oven back for brace. Works fine for a repair by a 65 year old woman.

Actually you are right, I removed the two screw pulled the element out , disconnected the two wires holding the old element and put the new one on. I spent more time finding out whether or not it would be safe to work on it, being on my own for the first time and always had someone do it for me. I was told as long as the oven was not on it was safe and so I went to work. I was also very impressed at the short time it took to get the part. Three days!!!!!!!!!!!!!!!!!!

Two screws to remove the element and two screws for the wire connectors and it was done.

First I turned off the power to the stove,removed oven racks,removed the two screws that held the element in place,pulled unit out a couple inches ,removed the two screws that held the wires in place ,removed element.
Placed new unit where old one went and placed wires in proper order and put together and placed back . turned power back on and WALAA......nothing......apparently that wasnt the problem....Husband baught me a new stove,after 35 years why not.

.....then tested for voltage, had it. Ordered the element through partselect.com and it came in the mail THE NEXT DAY! No kidding! Installed it and the wife is back to her good cooking. All is well, thanks partselect.com. John R., Pompano Beach, Florida

removed the old, replace the new. The delivery of my new part was exceptional, received the very next day after ordering.

Simple replacement. Price for replacement was excellent. Cheaper than any replacement I priced locally and arrived the day after I ordered.


Thanks!

Removed the two screws which held the element in place. Then I pulled the element out about 2-3 inches and disconnected the two wires. Of course I turned off the breaker which fed the range. This had been done earlier so that wife could throughly clean the oven while the element was out of the way, When the new element arrived, we put it into the oven, reconnected the wires to the lugs on the element, pushed it back into the hole, pushed the insulation which protruded back into the hole, and replaced the two screws which held the back plate in place. Turned the breaker back on and turned oven on to test the repair job. Everything worked AOK.

My sons helped with that. They had to use a pliers to remove the old screws (did not have to notches). After that they they removed the element. Then the wires had to be disconnected (after we unplug the oven from the main power source. Then the wires were connected to the new heating unit. We only got one screw in so far will work on getting the second one in when they return tomorrow. I did turn on the oven and it works!!!

Thank you to the nice young man that helped me on the phone.