RC776*05 Hotpoint Range - Instructions

The replacement was easy: turned off breaker to range; unscrewed element from range top;opened ceramic terminal box; unscrewed element from range wires. Then I simply reversed the procedure, using the new parts. Easy to do and it only took about 10 minutes.

These two repairs were straight forward and the repair does not need elaboration. The amazing aspect of this repair was that I ordered my parts and received them on the second business day without any additional charges. That was really fast ! Thanks Partselect.

A simple repair using your quality matched Part turned into a CONDOMINIUM CIRCUS (no fault due to the Part or PartSelect.Com.)

It was the 1st time in over 30 yrs. that we had to throw a Circuit Breaker Switch located outside in the communal large Metal Box between Condos. Not only did it NOT cut the power off our old GE Range - it turned off one neighbor's T.V. & another neighbor's Washer/Dryer Set.

As more Breakers were tried - MORE ANGRY NEIGHBORS ARRIVED ON THE PATIO. To complicate this - the next-door Condo just underwent extensive (read 3 Months) Renovation including REPLACING ALL WIRING..... and you might imagine the rest. No Breaker Switch numbers matched the Condo number written beside them in felt tip pen... it was complete chaos!
THANKS to PartSelect.Com our old G.E. is working again.

Yours truly,

William Rush,

Easy to do . Four screws,removed cover,removed switch. Installed switch,and cover. Time 1/2 hr.

i removed the two screws that hold the element in place. i then pulled the element out and disconnected the two wires. then i connected the two wires and screwed the element back in place and now it works like new.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Asked a local repairman to fix it. I saved money(saved $20.00) by ordering the broiler element from GE part select via customer service agent. The agent was informative and helpful. The part arrived the next day even with regular shipping cost. Impressed with the GE part select. Will use the company again.

I am left handed which sometime presents things in a aweward way. My greatest task was finding the right position and being able to hold the leads while trying to connect them. So I got a pillow and positioned myself and got into the oven and was able to do the job from there. After doing so, it took about 10 minutes to do the replacement.

It would have been easy, but the screws that came with the replacement burner were too long for the ceramic insulator to fit over. Had to grind down the screws fro 3/8" long to 1/4" long. After that, piece of cake.

We unscrewed the element easily enough, but had a hard time disconnecting the prongs. Once we did, we had to use a thin screwdriver to open the clamps to fit the new prongs into them. After all was accomplished and we switched on the breaker the broiler still didn't work. Either we did something wrong or the element wasn't the problem. We haven't decided our next move yet; whether to get a repairman in or buy a new oven. It's a pretty old oven/range.

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

Broiler element failed catastrophically (with light flashes) while in use (1986 GE self-clean oven/four burner stovetop). Part number embossed on element plate - very difficult to see - took digital photo while still in oven and magnified. Easy to search for part. Good price, prompt delivery. Removal of old and install new awkward because of access angle and my decreasing nimbleness, as well as oven control thermocouple and support bracket in way. But no technical difficulties. Hex head metal screws holding in element; Notched phillips metal screws holding bracing bracket (easier to put element in by removing one side of bracket). Screws difficult to remove as in much used oven 26 years, and thermocouple partially blocking socket ratchet wrench. Would have been easier with 1/4" short extension. Before detaching element, I used twist ties around the leads tied to a large plastic clip so as not to lose them into oven back. PartSelect part was made by GE, not secondary source. Perfect replacement for this old part - still available.

Even though my sons offered to do the repair, I opted to hire an appliance technician to do it and it took him at least 45 mins. with his experience and tools. apparently the inside wall wires were shorter and more difficult to access and grip and I'm glad I did. It should last another 20 years and I'll be dead!

The repair was easy once he read the directions. The part arrived about 4 days earlier than expected. Great company.

Replaced the old with the new following directions (mostly).