RK7670T3AD Hotpoint Range - Instructions

Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to test it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*

The first thing I did wrong was order the wrong part. Then later I did find the Model number on the side of the bottom drawer. I reordered the right part and turned off the electrical breaker. Removed the old element. I then installed the element in the oven with 2 screw nuts and pulled out the stove, took off the back panel and slipped the wire nuts onto the element. Very simple. I am really thankful there is a place to order the part and it came the next day after I ordered it. WHOW!

Hi, First unplug appliance ,remove the oven door by pulling it up from the hinges, giving room to work deep inside , remove the two screws that hold the element in place. then pull the element out carefully not to stress the wires and replace the element . Note after all is done test with an oven thermometor :)

Easily removed two screws, pulled the wires out of the oven wall, disconnected the old and reconnected the new, pushed it back into the insulation, inserted the screws and tightened them. There was a problem with the model number. It was on a vinyl plate inside the oven drawer wall. The plate was slightly yellowed so I used my finger to wipe the yellow away. When I did, the model number ended up as a black smudge on my finger tip. GE's engineers could have come up with a better method of displaying the model number. GE's customer service operator, however, did an excellent job of helping me to ascertain, at least, some of the number.

Just like your example said/turn the power off to the oven/remove the screws that hold the element in place and then I pulled th element out a little ways and disconnected the wires/reconnecting took a little longer only because it was hard to see/but I connected the two wires and put the screws back in and it worked. Saved me a lot of money/my husband wanted to get a new double oven

First, I shut off the power to the oven... no point in risking a nice electric shock. The next thing I realized was I could not see anything... enter the flashlight. Then, well then it was really easy. I removed the two screws that held the element to the back wall of the oven, pulled the element (and some of the insulation stuffing) out about 2 inches to reveal the two wires and their connecting screws. Unscrewed them, put the new element in, reconnected the wiring, restuffed the stuffing and reattached it to the oven wall. Turned on the power and she heated up faster than ever. Speaking of fast, my part arrived the day after I ordered it and that was with regular shipping. Thanks fellas.

First I removed the two srews that hold the element in place. I then pulled the element out about three inches and disconnected the two wires. I attached the wires to the new element and we had our oven working again. I really am happy with the timely service I received from PartSelect and would recommend them to anyone.

First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire connection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.

1. Cut power off. 2. Remove old element, make sure you do not lose the screws, pull the connecting posts out and we used strings on posts so they could not get lost in the wall. 3. We then replaced the new element with little of no problems, it took approximately 30-45 minutes for the whole process.

I initially only purchased the heating element since this usually the cause of the broil element not functioning well. It took a little longer to receive because I had to order it over the Holidays. Once it arrived it was very easy to replace. It worked very well after installation but the broil element still did not function. I then purchased the broil element and received it within approximately 4 days. It took just a little more time to replace because there was a brace that was attached to the upper oven that helped to hold it in place. Once the wires were attached with the screws it worked very quickly. It's nice to have my oven back in use again!

First shut off power to the range in the electrical
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)

My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!

took old element out , put new element in.very easy.

This range is about 30 years old and I was thrilled to still be able to get the bake element, which burned out about a month ago. I was doing research to buy a new stove when a cousin, from out of town, called to say they were going to visit the following week. No time now to get a new one installed. "partselect.com" was the fastest way. THANK YOU!

First off, I want you to know I'm an obese 56-year female without tools. But, I knew where to borrow those.

I first shut the power off to the range. I then disconnected the 2 screws that hold the element and pulled it out to reveal the 2 screws which connected the wires. I unscrewed those and removed the bake element. I double checked the stove model and bake element part # at the GE website and ordered it from "Partselect.com". It came in about 3 days. I then reversed the order of the above and it was done.

Here are some challenges I encountered..
1) The oven door was in the way making it uncomfortabe to get to the back of the stove.
2) Those $#%& screws are so short I kept dropping them.
3) The wires in the back bend easily. Be careful.

That's about it. It was a pill but not a real problem. It sure beat buying a new range before I've decided on which one to buy.

took cover off back of stove. Removed two screws and wires that were attached to the element. Removed old element and installed new element. An easy repair.