RB632G4N3 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nancy from Golden, CO
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The heating element in the oven failed, after at least 16 years of good service.
First, we turned off power to the range. We removed the screws holding the element to the back wall of the oven and pulled out the element a few inches. We disconnected the 2 wires from the old element, and attached the new element with the 2 provided screws. We pushed the element back into the wall and secured it with the screws. Turned the power back on, turned the stove back on and, voila, the frozen pizza was well on its way to becoming dinner!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mr Sal from Eastampton, NJ
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
element wont heat up
4 screws 4 off then 4 on done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Stuart, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Heating Element Was No Longer Working.
Removed oven door by holding sides and pulling upward. It's easy to remove and replace. Removed shelves by sliding back and up, then out. Removed two hex nuts with socket wrench. They are on back wall of oven and secure element to that wall. I then pulled element out about 3 inches and disconnected the two leads.
I put new element in, reconnected two leads, replace two hex nuts and was done.
Turn off power to stove at circuit breaker before starting.
I put new element in, reconnected two leads, replace two hex nuts and was done.
Turn off power to stove at circuit breaker before starting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from CARY, NC
- Parts Used:
- WB3X5699
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I knocked the timer knob off of my 30 year old GE range and it broke so had to replace it.
Simply put the new knob on and it worked perfectly. No tools needed. So glad to locate this website to purchase knobs that fit my range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lavona from JACKSONVILLE, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Bake element burned out
Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to test it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Grand Rapids, MI
- Parts Used:
- WB44X5082
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Really old range. Broken bake element in oven.
Turned off power. Removed old broken one installed new one in minutes. Turned power on and tested it out. If this 60 something lady can do it, you can too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREGORY from HOUSTON, TX
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake Element Burnt Out On Upper Oven
Unscrewed the element from the oven,disconnected the two screws for the electrical and reverse the procedure to install new element. Took all of about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Sewickley, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven wouldn't heat
Couldn't be a much simpler repair. You pull the old element off by removing two screws. Then you slide the old element toward you several inches and remove the two screws holding the wires that are attached to the old element. To replace, just do everything in reverse. One cautionary measure, even though the oven is off, there is still a small amount of electricity going to the element. Turn the stove off at the circuit breaker, or unplug the stove before you attempt the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from TRAVERSE CITY, MI
- Parts Used:
- WB2X831D
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
bottom drawer guides
Snapped in place (4)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from BETHLEHEM, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The bake element burned in half.
First I turned the power off to the oven/stove at the breaker box in the basement. Then I took the back plate off. Then I removed the two screws holding the wires onto the damaged element. Then I removed the two screws holding the element to the inside rear of the oven. Then I pulled the old element out and replaced it with the new element. I replaced the two screws that hold the element to the inside of the oven. Then I replaced the wires on the element where it protruded at the back of the oven. I put the back plate back on, slide the oven back in place and turned the power back on at the breaker and everything worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from Cave Creek, AZ
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Baking element no longer worked.
Removed 4 screw nuts and replaced with new baking element using same 4 screw nuts. Real easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas Minich from South Windsor, CT
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element burned out due to age
Shut off the power at the circuit breaker, removed the two nuts holding the element to the oven, unscrewed the two screws connected to the wire leads, removed the bad element and reversed the process to replace with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Bend, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The small element blew out consequently shorting out the infinite switch.
The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.
Was this instruction helpful to you?
Thank you for voting!
One burner was not level and the otherone I burned out tea kettle on it and when I pulled the kettle off the burner it was also not level not to mention part of the kettle was burned onto the burner.
I didn't turn the power off which was risky and dangerous, however it was very easy just removing one screw a couple of wires and installing the new one. VERY EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AL from GENOA, NE
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element burned out in oven
First shut off power to the range in the electrical
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)
Was this instruction helpful to you?
Thank you for voting!