RHV786*05 Hotpoint Range - Instructions

My husband was able to easily remove and replace the switch and know with-in 15 minutes.

First turn off breakers. Undo all screws and remove burner. Easy to see how to replace old part with new. Self explanatory if you follow what you have taken apart.

Just re-connected the electrical. Was the exact/correct replacement part. Repair successful. Thanks.

Just unpluged the old one and detached the wires. put the new one in and used a socket wrench to rewire it. . Very easy and was shipped in perfect condition and easy to replace. Very pleased.It fit perfect and oven works just fine. Thank you so much for the service which was very speedy. It was packed to perfection.

I diagnosed the problem as a burned out element. Received the part the next day (very quick service) My husband replaced the old element with the new. My broiler still doesn't work. I don't blame the company, my diagnoses was wrong. I have called the appliance repairman and it will probably be an expensive fix.

The broil element was easy to replace. Start by either unplugging the unit from the wall or turning the circuit breaker off. I started by removing the two screws that hold it in the back. There was a support bar attached to the top with two screws also. After removing all screws, gently pull the element forward exposing the two wires. Make note of which wire goes to which terminal. I also clipped a clothes pin to each wire to prevent them from falling back through the hole. Disconnect the two wires and reconnect to the new element. Reattach all screws and you're done.

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.

Turned off the breaker to the range. Turned on range to ensure no electricity was currently flowing to the range. Turned the range off and unscrewed the tilt lock hinge. Pulled the burner out to expose the wires. Popped the snap locks off the cover box and unscrewed the wires connected to the posts. Followed recommend directions to expose approx. 1/2" of new wire (this is what I used the knife for since I did not have a wire stripper available). Slightly cut thumb in the process (no blood, though). Removed old burner. Put new burner in place, re-attached wires to the posts and screwed in to place. Placed cover box back in place and secured using new snap locks. Attached tilt lock hinge using new screw that was provided. Turned breaker back on and turned on range. new burner worked great. Took about 20 minutes total. Wife was extremely impressed, mostly that I didn't electrocute myself. She now wants me to replace other three burners. No good deed goes unpunished.

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

First I turned the power to the stove off at the breaker box. Next I removed the two screws holding the old element in place against the back wall of the oven. I gently pulled the element forward. I wound a couple lengths of spare colored wire around the two electrical wires before disconnecting the retainer screws at their connection points. This insured that the electric wires would not fall back inside and behind the firewall. I then disconnected the screws holding the electrical wires to the broiler element. I removed the element from the oven and discarded it. I then connected the screws through wires and the connecting points of the new element. I removed the spare wires hold the electrical wires. I positioned the broiler element in place and screwed in the retainer screws securing it in place. I turned the breaker switch to the "on" position and tested the new broiler element. It tested fine. Job done in 15 to 20 minutes. An able bodied person could do it in less than 10 I'm sure.

I am left handed which sometime presents things in a aweward way. My greatest task was finding the right position and being able to hold the leads while trying to connect them. So I got a pillow and positioned myself and got into the oven and was able to do the job from there. After doing so, it took about 10 minutes to do the replacement.

It would have been easy, but the screws that came with the replacement burner were too long for the ceramic insulator to fit over. Had to grind down the screws fro 3/8" long to 1/4" long. After that, piece of cake.

We unscrewed the element easily enough, but had a hard time disconnecting the prongs. Once we did, we had to use a thin screwdriver to open the clamps to fit the new prongs into them. After all was accomplished and we switched on the breaker the broiler still didn't work. Either we did something wrong or the element wasn't the problem. We haven't decided our next move yet; whether to get a repairman in or buy a new oven. It's a pretty old oven/range.

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?