RH758G0J3 Hotpoint Range - Instructions

I took out the old broiler support bar, but it was being held by one screw. I did install the new bar with one screw, but I need to obtain a second screw. I still have not located a second screw, but it is inplace.

Installed new knobs, mom is happy!!

Partselect made this job a breeze. Due to the user friendly process to order and receive the part. I repaired the stove after turning off the breaker in the main box. There were two screws that held the baking unit in place, removed them and then replaced with new unit.

Removed existing surface element and replaced with new element.

P.S.

Part Select service was excellent.

Got new part! Unplug range!!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!

I unplugged each element from the terminal it was plugged into and then plugged the new element in. I also replace the drip pans and trim rings while I was at it.

First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.

Removed 2 nuts holding the baking unit to the oven back, removed 2 nuts holding wires in place, installed new unit following procedure backwards. It takes longer to get the tools,take the oven door off, and take racks out than it does to remove and replace the baking unit.

orderd new gasket part removed oven door disassembled installed new gasket reassembled works great just like new

When the part arrived, I used the diagram provided by the website to see what really needed to be done. Keep in mind, if you're doing it correctly and disconnect the range from the power source, it's going to be dark inside the oven. Get a good flashlight or electric lantern. There are two screws holding the element in. Mine were 8MM hex-head screws, but be prepared for anything. I removed the with a socket attachment/adapter to my cordless drill/screwdriver, and the part came right out. Some insulation will come as well - don't panic. Installation is similar, just in reverse order. Pay attention to the feet on the element. Make certain they are down. Don't lean on them when you think you're finished and discover that you installed it upside down like someone I know, and have to pull it out to correct this.

I first removed the unit by pulling gently from connection. Replaced the new one in that same manner - simply inserting into connection.

Very easy, I'll probably try it again soon.

I had purchased a partselect heating element for my larger lower oven previously so I knew what to expect on replacement.

I shut off the power to the stove from the electrical box. Next I removed both the cooking racks from the oven. Then the side removable panels and bottom as this is a P7 removeable panel oven. This gave ne easy access to the nuts/screws holding the element in place. Once the screws were removed I pulled out the element and disconnected the leads. I replaced the new piece reversing the process.

Because of the superb pics and descriptions on the Part Select site, I was able (with NO range model number) to order the correct range element for beloved son's stove. He plugged it in in 3 seconds, works great !

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

I removed the unit easily with anut driver, however the unit also supported the thermo-link. I had to use the hack saw to relieve a small opening for the thermo-link to pass through. No real problem. Then a few holes to be drilled to attach the 'link' to the base of the broiler unit.

BUT-I went into the website listed on the box. GEAppliances.com Guess what? Their price was twice yours!!