GGF356BBWB Gibson Range - Instructions

The front glides easily snap into a hole on the sides of the range. The rear glides easily snap onto the sides of the lower rear of the drawer.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

First I turned off the circuit breaker to the oven. Then, I removed the base of the oven (the oven floor) by easily removing two screws. I also removed the flame guard by removing a screw. That easily exposed the old oven igniter. I removed the two small screws that held that in place. The igniter is connected by two wires, which you'll have to snip. Snip those very close to the igniter (leave about an inch of wire on the igniter). Using a wire stripper, remove about 1/2 inch of the outer sheath of the existing wires. On the new igniter, snip the wires leaving about 2 inches still connected to the igniter. Using the wire stippers, remove about 1/2 inch of the outer sheath. Using the plastic wire caps that came with the new igniter, connect the wires from the oven to the corresponding wire on the new igniter. Screw the new igniter back in place. Replace the flame guard and oven floor. Turn on the circuit breaker and start cooking again!

snapped the new piece of plastic in its place and ta da, its fixed.

It was a replace racks not repair. No problem

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

Very easy just had to pull the wire up that holds it secure.

My Tappan Tail:

Open the oven and remove the racks, turn on the oven light.
Remove two screws in the back to remove the bottom plate. Mine are about 1 1/4 in. long.
Remove one nut holding the butterfly plate in place. Ignitor will be exposed.

Turn off the oven light and unplug oven. Don't drop the plug behind the oven, I was ready for that one.
Drop light or flash light will be needed, it's dark in there. And something to sit on, 16" old plastic milk caddy, I just happen to have one.

Remove the two screws holding the ignitor, don't cut the wires just yet. Take note where the wiring runs. Install the new ignitor. My wires went behind the gas piping.

I cut the bottom wire from the old ignitor first, up close to the ceramic. Wire shield can be reused, slide it over the new wire. Cut the old wire, leave a lot. Trim the new wire to desired length and strip the ends of both and use the ceramic cap and connect the wires.
Do the top wire.
Slide the wire shield next to the igniter, adjust the wires so the wire shields won't slide away from ignitor. With the butterfly shield back in place it's time to plug it in and give it a test.
Nice.
Replace the bottom plate of oven, screw holes hard to find. Had to use an awl to find the holes to line up the screws. I also didn't push the front of the plate down into place until I had the screws started. It helped.

You might think this is overkill, but how many of us have ever replaced the ignitor. Not me.
I do a lot of DIY's. I'll rate this as a 1, easy.

What shall I bake first, cornbread of course. I my cast iron skillet.

get liquid wrench, remove oven door(2 screws) remove oven bottom(2 screws) follow directions included with part. unplug or shut off electricity at breaker panel, Have a good light source.

Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.

First removed oven racks then two screws to remove oven door, removed two screw of oven fan cover, ( need to remove fan cover to have clearance to removed bottom cover of oven) removed bottom cover of oven, then removed two screws holding oven igniter and cut wires of old igniter then spliced wire of new igniter to existing wire and reassemble in reverse order.

Removing the drip pan and the bottom burner cover exposed the igniter, removing two screws retaining the bracket freed the old igniter. Removing the warming drawer allowed access to the control module to unplug the wiring on the ignitor. After making myself a diagram, I unplugged the wires and removed the malfunctioning igniter. Cutting the leads off the old igniter long enough to splice it on below the oven bottom with the enclosed wire nuts and attaching the new igniter (reusing the old insulation to protect the wire) took only minutes and reassembly was straightforward.

New igniter: $60
Repairman fee saved $150
Being able to tell my wife "See,
I told you I could fix it!" PRICELESS

switch out wires on spark module same burner would not lite
oder burner instead of igniter for four dollars more for new burner and igniter it made sense. Changed burner out burner works
thanks
Ron

Disconnected the oven from the wall outlet. Removed the bottom panel of the oven to reach the parts. Reached in the thight spot (not for a big guy)to unscrew the old igniter. Installed the new one. Plug the oven back. Turn the oven on bake at 350. Oveb lighted up in 5 seconds ! Working great since then!!!