JSC27G404 General Electric Range - Instructions

the replacement items fit really good. It was a matter of remove and replace,

Just pushed the new timer knobs onto the stem. They fit and now I can set the oven timer without having to use a pair of pliers to grip the stem and turn it.

Two of the knobs fit perfectly.

The stem for the the clock was broken off and there was not enough of the stem left for the new knob to fit.

When the part arrived, I used the diagram provided by the website to see what really needed to be done. Keep in mind, if you're doing it correctly and disconnect the range from the power source, it's going to be dark inside the oven. Get a good flashlight or electric lantern. There are two screws holding the element in. Mine were 8MM hex-head screws, but be prepared for anything. I removed the with a socket attachment/adapter to my cordless drill/screwdriver, and the part came right out. Some insulation will come as well - don't panic. Installation is similar, just in reverse order. Pay attention to the feet on the element. Make certain they are down. Don't lean on them when you think you're finished and discover that you installed it upside down like someone I know, and have to pull it out to correct this.

Replaced the burner. Still no heat. Decided to take the front off and test the connections (Power Off!). Found no output from switch to burner. Ordered new switch from PartSelect. Switch arrived in 24 hours, just like the burner (I'm in FL, but still fast!) My only problem was that the know didn't quite fit -- too long. Cut the metal correctly, but still too long. Had to cut the plastic adapter slightly. Now it fits like the others, but it's not quite as secure due to shortening the piece that slides on the metal shaft.

Read and follow the instructions. Be careful when stripping old wires to attach to new element. Fit the element to ceramic casing prior to attaching wires. If new element does not seem level after replacement heat a large pot of water. The element will expand and the weight of the pan of water will settle the element. "Physics 101"

Gasket sent did not match the profile of the original. Only after trimming off two long edges of the gasket did it come close to matching the original. I would not recommend using this replacement gasket for this oven model. 1-Remove door. 2-Loosen the 2 oven box attachment nuts on the back of the oven. (loosen only, about 3/8") 3-slide the oven box toward the front of the oven. 4-remove old gasket, and insert new. 5-Retighten 2 oven box attachment nuts. 6-Reinstall door. Took especially long because of incorrect gasket. Deep well socket required to loosen oven box attachment nuts. Recommend two people to do, one in back, for attachment nut and one in front to keep gasket in place while tightning nuts.

Took off the door, took out the two screws in the back of the element. Then pulled the element forward, then removed the two wires. Then put it all back together with the new element.

Ordered new burner and drip pan. New parts arrived within 3 days. Removed screw holding the hinge, removed clips from porcelain insulator, removed old burner, then installed new burner, reinstalled tilt lock hinge, replaced drip pan and ring and set burner in place. The whole installation took less than 10 minutes, and it works perfectly.

Turned off power to the oven at the circuit breaker. Pulled the old heating element from the back lower wall of the oven. Noted the position of the wires (right terminal attached to the red wire, left to the black wire). Removed small bolts holding the element to the wires using pliers. Attached the new element using screw driver. New element came with screws, not bolts. Pushed the element back into place and restored power. Tested to make sure everything worked. Everything works and I ran an oven cleaning cycle. Noticed that indicator light above the temperature selctor is always on now even when oven is in the OFF position. Not sure if that's related to the change or to the oven cleaning cycle I ran. In any case, oven seems to work normally.

First I turned the breaker off the Range. Second I removed the two screws that held the element inplace. Then I pulled element front until I could get to the two screw which connected the wires and removed then. Removed old Bake element. Installed new element by connecting the two wires and then pushed the element into place and secured it by reinstalling the two screws. Turned the breaker back on and tested. This is a very easy item to replace and takes very little time.

First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire connection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.

Easily removed two screws, pulled the wires out of the oven wall, disconnected the old and reconnected the new, pushed it back into the insulation, inserted the screws and tightened them. There was a problem with the model number. It was on a vinyl plate inside the oven drawer wall. The plate was slightly yellowed so I used my finger to wipe the yellow away. When I did, the model number ended up as a black smudge on my finger tip. GE's engineers could have come up with a better method of displaying the model number. GE's customer service operator, however, did an excellent job of helping me to ascertain, at least, some of the number.

Just like your example said/turn the power off to the oven/remove the screws that hold the element in place and then I pulled th element out a little ways and disconnected the wires/reconnecting took a little longer only because it was hard to see/but I connected the two wires and put the screws back in and it worked. Saved me a lot of money/my husband wanted to get a new double oven

First I turned the power off to the oven/stove at the breaker box in the basement. Then I took the back plate off. Then I removed the two screws holding the wires onto the damaged element. Then I removed the two screws holding the element to the inside rear of the oven. Then I pulled the old element out and replaced it with the new element. I replaced the two screws that hold the element to the inside of the oven. Then I replaced the wires on the element where it protruded at the back of the oven. I put the back plate back on, slide the oven back in place and turned the power back on at the breaker and everything worked.

Removed 4 screw nuts and replaced with new baking element using same 4 screw nuts. Real easy job.