JBP25G2R1 General Electric Range - Instructions

I removed the 2 screws and the 2 wires from the broken heating element. I removed the broken oven heating element. Then I attached the 2 wires to the new heating element and put the 2 screws in to attach the new heating element into the oven. The new oven heating element worked just fine and I was done.

First I turned off the circuit breaker leading to the oven. Then I removed the two screws that held the old element in place. I pulled out the element and disconnected the wires. I reconnected the wires to the new element and pushed it back in place. I then secured it with the two screws. I turned the circuit breaker back on and turned on the oven. Works just great!!!

remove screws attaching burner plate to back of oven, pull out element, undo wiring to old burner by unscrewing 2 screws, remove old burner, reverse process to put new burner in

Easily removed two screws, pulled the wires out of the oven wall, disconnected the old and reconnected the new, pushed it back into the insulation, inserted the screws and tightened them. There was a problem with the model number. It was on a vinyl plate inside the oven drawer wall. The plate was slightly yellowed so I used my finger to wipe the yellow away. When I did, the model number ended up as a black smudge on my finger tip. GE's engineers could have come up with a better method of displaying the model number. GE's customer service operator, however, did an excellent job of helping me to ascertain, at least, some of the number.

took old element out , put new element in.very easy.

I loosened two screws that held the baking element to the stove and pulled out. Then, with a screwdriver , I took the old wires off and replaced them onto the new Baking Element and reassembled.

It was a very easy task and while I was at it,I replaced the Drip Bowl pans on the top of the stove with Chrome ones.

I ordered the parts on a Tuesday and, to my surprise, I received them on Thursday, and the cost was about half of what it would have cost me elsewhere (to include GE Parts Warehouse)

I highly recommend partselect to all of you that need inexpensive repairs.

Firs I shut the power off to the range. Then I removed the bottom oven rack, then removed the two screws holding the element in place. I pulled the element out about 3 inches to pull the connecting wires off. However, when I pulled the element towards me a lost on of the connecting wires that attached to the element. I then had to pull the range away from the wall and remove the back cover panel.I then fed the new element into the wholes from the inside of the range and having the back panel removed gave me full access for reconnecting the element wires. I put the back cover panel into place , put the bottom oven rack in and that was it. I was done with the repair. I turned the power back on and everything worked fine. I would recommend removing the back cover panel prior to trying to remove the element. This will save you some time and give you full access to the wiring before attempting to remove the bake element.

Couldn't be a much simpler repair. You pull the old element off by removing two screws. Then you slide the old element toward you several inches and remove the two screws holding the wires that are attached to the old element. To replace, just do everything in reverse. One cautionary measure, even though the oven is off, there is still a small amount of electricity going to the element. Turn the stove off at the circuit breaker, or unplug the stove before you attempt the repair.

The only hard part about putting in a new terminal block (and this time I had to replace the burner too, because that fried too) is stripping the stove wires, because that thermal insulation is very hard to get off. Otherwise, it's simple. In this case, I had already replaced this one (sigh), so had already cut & stripped the wires, so it was all easy. Frankly, the sane thing to do is buy a new stove, but wife is too cheap.

First I read the already posted repair stories to give me confidence I could perform the repair.
Followed their steps -
Removed the two screws holding the plate to the oven.
Pulled out the element.
Removed the two screws holding the wires to the element.
Installed the new element by attaching the two screws (which were supplied) to the element.
Reinstalled the plate to the oven.
Tested it and it worked perfectly saving a costly service call.

The part was delivered in 24 hours with regular
shipping and was simple to replace. Uncrewed
it, disconnected wires from the old one and connected
the new one. Cost a little more than $30 including shipping and the oven works great!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Removed the old piece and connected the wires to the new piece. I'm a woman and this took me less that 15 minutes to complete. Easy as pie. On top of that, I received my order within 3 days! Very impressive, PartSelect. Thanks.

It was so easy. Just removed the cover and then unscrewed the wires (keep track of which wires go to which side). Do teh reverse to reinstall

Repair was as easy as one, two three. Turned off the power and removed the two screws holding the element in place. Then pulled the element out approx. 3 inches and removed the two screws connecting the wires to the element.

From there I reversed the process and the repair was complete in less then 5 minutes, and I am not a electrician.

I turned off the electricity, unscrewed the old one and disconnected the electric wires, then put the new one in just like the old one. It was very easy and now it works great.