J785004AV General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stacy from Houston, TX
- Parts Used:
- WB44X173
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Old Broiler Ekement burned out
The removal- replacement problem basically involves the shortness of the connector wires to the terminals. Because the burner is close to the top there is little room to use a screwdriver. The old unit used metal screws. The new came with open threaded holes in the terminals with two threaded screws. Used a small 1/4" ratchet which worked OK, but had to carefully bend the ends of the terminals to allow me to lower the element to an angle that would all room for ratchet action. (All design engineers should first have to work in maintenance before going to drawing board!)
S. Cooke, Houston Texas
S. Cooke, Houston Texas
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Harvard, MA
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The control knob stem broke off when I moved the stove.
I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from peabody, MA
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
replacing old rusted drip pans w/ rings
simply lifted the heat coil and slid the rings off and lifted the drip pans off. Vacumed the bottom underneath the old pans. Cleaned the grease off around the stove where the rings sat. Let it dry and added the new rings and pans. Looks like it did 30 years ago.......let them try making a stove last that long today !! Make sure the power is OFF at the electrical box.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from redding, CT
- Parts Used:
- WB17X5051
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Stove element not working
The only hard part of the job is removing the old, corroded terminal block. Be careful not to break the electrical wire. Other than that, just sand the contacts and reassemble. This is the second one I have replace on my 4 burner stove. 2 more to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Concord, NH
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Broil Element
Replaced damaged element exercising the care suggested in repair comments by previous customers. Old unit had screws connecting the broiler element to the stove's electrical supply wires, which were difficult to remove due to old age. Just took a little extra care to ensure that supply wires were not damaged during disconnect and after reconnecting the new element the broiler tested OK. It is once again broiling steak to perfection
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Chapel Hill, NC
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace Broiler Element
After an exhaustive search of local oven dealers and big box stores, I could not find a broiler element for my aged GE stove. I did find it online at Parts Select for about 1/3 the cost from GE online parts.
Replacement was easy-- just as described in posts for this part. The 'hardest' job was getting the screws started that hold the wires to the element-- small screws and small holes-- but just required some patience. A simple, inexpensive repair that avoided my having to replace the entire stove. Thanks!
Replacement was easy-- just as described in posts for this part. The 'hardest' job was getting the screws started that hold the wires to the element-- small screws and small holes-- but just required some patience. A simple, inexpensive repair that avoided my having to replace the entire stove. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kitty Hawk, NC
- Parts Used:
- WB32X10013, WB31X5014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed to replace drip bowl and trim ring
The replacement drip bowl and trim ring fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louise from Wesley Chapel, FL
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced trim rings and drip pans
Simple replacement on an old "built in" range in good condition but drip pans and trim rings soiled beyond cleaning. Stove top, although 20+ years old, now looks like new. So glad to find parts were still available as "universal" replacement parts for the 8 inch burner do not fit. Delivered to my door in days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Kempner, TX
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls could not be cleaned
Replaced drip bowls.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from WEST POINT, UT
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
broil element had a "burn through", w/n turn on
less than 15 minutes R2 the part, ops ck'd good. 4ea 1/4" screw/nuts, they didn't fight me...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Gate City, VA
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old and rusted rings and pans
lift stove eyes and replace
Was this instruction helpful to you?
Thank you for voting!
Old trim rings were rusted and soiled
Too easy to describe. Just lifted out the old rings and popped in the new ones. PartSelect is my go-to source for appliance parts both for my home and my job as maintenance man for residential group homes in my area. Website is easy to use, prices are good, shipping is always surprisingly fast. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from West Melburn, FL
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original parts lost or discarded by prvious owner
Just replaced drip pans and rings on stove
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Garden City, NY
- Parts Used:
- WB17X5051
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Element was no longer heating up
I turned off the circut breaker and disconnected the old terminal block - some difficulty removing the wires because of corrsion - I was able to reconnect the wires to the new block quickly and I was done - fast and easy - so happy to have found the part so easily with your program. Thank you
Was this instruction helpful to you?
Thank you for voting!
Old and corrosive due to age
After receiving parts, was getting rims unpackaged and removing the old rims, then and installing the new ones. Extremely easy to do. No tools needed
Was this instruction helpful to you?
Thank you for voting!