JCBP23WK1WW General Electric Range - Instructions

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

I first unpluged the stove then removed the 6" element then I removed the back panel on the stove located the wires that went to that element unplugged them and removed the block then fished the wires through for new terminal block installed in terminal block bracket then pluged in wires put element in place put back panel back in place plugged stove checkout heat on element good to go 20 min

Shut the power off and unscrewed facial hardware ,unplugged terminal and unscrewed hold down bracket and redid everything that I mentioned above. For a rookie it was a piece of cake.

First we removed the screws inside the oven. Next, the oven backing was removed by unscrewing one side and one bottom bolt which exposed the clips for the burner. The clips were removed from the old burner. The old burner was pulled through the fiberglass protection and out of the oven. The new burner was inserted into the oven and the prongs were pushed through the fiberglass protection. The screws inside the oven were reattached. The clips were attached on the outside of the oven. The backing was slid into the right holding piece and the bolts on the left and bottom were attached.

Pull out the range. Pull out the electric plug. Unfasten the back panel. Raise the range top. Replace the terminal block in exactly the same position as the old one. Put everything back.

This is the third time I have replaced it so it is very easy now. This time I spent a little more time making sure the burner element prongs were just just like the others. Must have been a little loose in the block.

Removed the back cover with a socket tool, unplugged the old terminal and plugged in the new one. there is a screw holding the terminal block. so easy.

remove the door, removed about six screws and did a clean up on the glass. the replacement part was screwed back in place. so easy

Replacing the Surface Burner Terminal Block Kit was very easy.

1. Pull the stove from the wall a little so you can have space to work. I unplug the stove from lthe 220 outlet. Then remove the Surface Burner element.

2. Then we removed the back pannel from the stove by removing the screws with a nut driver. Only four screws to remove.

3. Once the pannel was removed. I Unpluged the wires from the stove pannel. Being careful not to damage the plug in. There were only two wires to unplug. So trace the wires to make sure you are unpluging the correct one.

4. Lift the top up on the stove and unscrewed the Terminal Block from the top of stove. We only have one screw there.

5. Pull the Terminal Block and wires out and replace with the new Terminal Block, making sure the wires were feed along the side under the top of stove so they can not be damaged. Plug in wires and replace pannel.

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

The wire to the burners were old and needed replacement. When the new terminals arrived, my husband had gone hunting. When the parts arrived, I pulled the stove away from the wall and found the nut driver that I needed. I removed the screw on the terminal box under the burner and realized I had to remove the back panel of the stove. I unplugged the old wires and plugged in the new ones. I installed the new terminal boxes under the burners and plugged the burners back in. My stove works like new and I am thrilled that it was so easy. Thanks

Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.

Replace the sucket for the heating element.

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

Turned off circuit breaker, removed screws holding old element in with nut drivers, pulled out old element about 3-4" to reach terminals connected to back of element, removed spade lug terminals with needle nose pliers. Reconnected terminals to new element and screwed new element in place with nut drivers. Turned on circuit breaker and oven. New element works perfectly. Took about 8-10 minutes. Very easy to do.

I can add nothing to the video you furnished on your website. I am generally all thumbs with home repairs - especially anything electrical - but, your video led me right through it. A good experience. We'll do business again.Thanks.