JGB700SEJ4SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lisa from INDIAN RIVER, MI
- Parts Used:
- WB31X49806
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Scratched griddle
Opened box. Took griddle out. Picked up existing griddle from gas stove and threw it out. Set new griddle in its place. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BRADENTON, FL
- Parts Used:
- WB21X20262
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Burner Valve stopped working
Turned off gas, then lifted up the burner cover and removed the old valve using a screw driver to loosen the clamp. I also had to remove the face plate using a socket set (4 screws). I didn't align the valve using the existing valves as a guide and also didn't get the clamp tight enough. So I re-aligned the valve to match the other valves and also tighten the clamp enough as best I could to prevent gas from leaking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BROWN DEER, WI
- Parts Used:
- WB03X24818
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Knob lost rear clip.
Ordered a replacement knob. Very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard B from CLARKSBORO, NJ
- Parts Used:
- WB28K10222
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Large burner cap finish was damaged
Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from LANSDALE, PA
- Parts Used:
- WB20K10027
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Replaced temperature sensor
un-screw temperature sensor, have to move racks and door, then open back cover board to disconnect the sensor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trilby from SAINT LOUIS, MO
- Parts Used:
- WB03X24818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The knob on the stove simply came off, couldn't get it back on no matter which way i tried.
It was very simple, I just simply took the new knob and inserted it into place without any problems, took no more than about ten seconds, works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SARATOGA SPGS, NY
- Parts Used:
- WB18X31213
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Igniter failed to stop firing after turning burner off
Used video from YouTube. Presenter recommended unplugging appliance before commencing repairs, but I do not recall a recommendation to shut off the gas supply. When replacing the harness you must disconnect the gas supply rail temporarily. Best to shut off the gas supply to the appliance prior to disconnecting. Otherwise, very straight forward repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from SPOKANE, WA
- Parts Used:
- WB2K68
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom part of the Drawer Glider broke off on both sides of the drawer.
Remove the draw from the stove. Then unscrew two Phillips Head screws ( one on each side). Remove the old gliders. Slip in the new gliders. Screw the two phillis head screws back in. Make sure when you put the drawer back in the stove that you lift the front of the drawer up enough that the lower portion of the new glider is engaged on the side rail of the oven drawer space.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from ROANOKE RAPID, NC
- Parts Used:
- WB28X24762
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Stripped gas pipe where the orifice goes
I found it to be much easier to take the entire gas pipe out replace the oriface then put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from PASADENA, TX
- Parts Used:
- WB29K10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Food ran over the burner and damaged it.It was easy to place it back inII
It only required placing the new burner in the proper location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Sheboygan, WI
- Parts Used:
- WB35X29668
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Oven door gasket was damaged and leaking
I watched the repair video on YouTube and followed his instructions as much as possible. Went pretty well as I thought it would be harder. I’m pretty handy so, I was pleased.
Was this instruction helpful to you?
Thank you for voting!