JSP34BD3BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michele from Dayton, NJ
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element was not working in an old (50+ years old)GE electric oven
Replacement of the heating element only takes a few minutes...First, turn off the breaker/fuse to the stove, then just remove two screws , pull out the two connected wires to expose the connections, hook them up, and replace the screws to the cover plate. The connection/cover plate can be hinged or not hinged. Make sure you order the correct one. We ordered the wrong one at first, but were assisted by the returns dept. and received the correct one in 2 days. Great customer service, thanks partsselect.com!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Muncie, IN
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Tenant broke bake element
Removed the two screws, pulled out old element, installed new element, and reinstalled screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MARTIN, GA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
bake element was fried
I went by the video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from BLUFFTON, SC
- Parts Used:
- WB30M1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken heating element
remove broken heating element and install the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PROVO, UT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls were badly tarnished . . . shine could not be restored.
1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod unit and bowl into the hole in the range top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Franz from CRESTVIEW, FL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not heat
Removed old broken element and installed new one. Took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WEST WARWICK, RI
- Parts Used:
- WB30M1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
a plug on the element broke off while cleaning and replacing
Absolutely no tools required for this task. Simply align the prongs to the female portion on the stove top. Carefully push in until the element is in place then line up with the drip pan slot. No instructions are necessary!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from PALM COAST, FL
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shortage in wiring cause the housing to burn out
Replaced new light housing.
Thanks to you guys for the prompt response
Thanks to you guys for the prompt response
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Mountain View, CA
- Parts Used:
- WB30M2
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Shorted out the burner... fat gets into the receptors on these old stoves.
The only hard part about putting in a new terminal block (and this time I had to replace the burner too, because that fried too) is stripping the stove wires, because that thermal insulation is very hard to get off. Otherwise, it's simple. In this case, I had already replaced this one (sigh), so had already cut & stripped the wires, so it was all easy. Frankly, the sane thing to do is buy a new stove, but wife is too cheap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Charlotte, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
My heatng element blew up
I followed the way all the others on this website did the repair. It was so easy. I turned the power off to the oven, then disconnected it from the back oven wall, pulled it out a bit, disconnected the wires, and put it back in.
Then we put the power back on and stood back and turned on the stove and IT WORKED!!! Yeah, and for so little money... I tell you I shopped other websites and this one was priced GREAT, and just reading the stories how others had done this repair gave me the confidence to do it too. Now, I think I have a burner that I will replace and who knows what else I can find to do.
THANKS SO MUCH!!!
Then we put the power back on and stood back and turned on the stove and IT WORKED!!! Yeah, and for so little money... I tell you I shopped other websites and this one was priced GREAT, and just reading the stories how others had done this repair gave me the confidence to do it too. Now, I think I have a burner that I will replace and who knows what else I can find to do.
THANKS SO MUCH!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Garden City, ID
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed New Burner Bowls
Removed the old burner bowls, replacing them with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Corvallis, OR
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Replace bake heater element
Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derrick from Ypsilanti, MI
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Oven no longer heated except for Broil element
1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- allen from MT. AIRY, MD
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
bake element was broken
i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!
Was this instruction helpful to you?
Thank you for voting!