JGSP48SH1SS General Electric Range - Instructions

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Followed the instructions that were sent to me by E-Mail.

remove two bolts in on sensor and slip thru back un plug and reverse to put in

Took about 15 minutes to take the old one off and put the new one on. Not difficult at all.

After reading reviews about corroded screws causing difficult removal I sprayed penetrating oil prior to installing replacement part. The oven doesn't need to be pulled out to fix. Just carefully pull wires through hole until the locking plug is visible & swap out. Very easy repair.

Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.

Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!

pulled out appl,removed door,racks,lifted oven bottom to remove,removed both oven and broiler ignitors---went to back of appl to remove gas control valve and replaced--used old oven ignitor in broiler(took chance it would work-it did!)installed new ignitor in oven--tested perfectly--point of info if you have an oversize or dancing flame in oven or broiler--remove flame tube and with 1/2 inch open wrench tighten orfice all the way until it stops--don't force or over tighten-- (the air shutter should open all the way)--flame should be about an 1 inch with white tips--adjust as needed-overall repair including adjustments took about an hour-hope this helps--and i'm not a professional repairman

I removed the racks, burner cover, then unscrewed the cover for the starter. Had to get the correct ratchet to remove screws. The hardest part was removing two screws that held the igniter in place. Difficult location to get the tool in. They were also hard to put back. After that it was a matter of pulling the igniter out and disconnecting it. You also have to remove the drawer under the oven so you can unplug the stove.

Read the experience of others on this website with the same problem. I knew exactly what to expect and it all went as the dozen previous oven repair experts had said. I can add my name to the list of experts. The two screws attaching the igniter to the bracket twisted off exactly like everyone else experienced. GE really should look at developing a better attachment. My only problem was because my drill was larger than the bottom of the oven. I had to drill the holes on an angle. One of the holes was wallowed out more than the other. I had to use two different size screws and they were more difficult to screw in. Bottom line; I saved money, the oven works, my wife is happy, so I'm happy.

Owners manual provided no help. Thankfully, the internet did. Internet convinced me the problem was the igniter, and with hindsight that was correct. 30 mins on the net to troubleshoot. On my model, the oven door must be removed to remove the bottom splash shield. Internet to the rescue to show how to remove the oven door. 10 minutes on the 'net, 30 seconds to remove door. Heat shield came out in about a minute. First machine screw that secures the igniter to mounting bracket out in 45 seconds. Second machine screw stripped in two wrench turns. Since the location of the mounting bracket was a cramped space (in a "well"), had to hand hold a hacksaw blade to cut off the head of the stripped machine screw. With only 3/4" of possible travel, this took 90 minutes. Then drill out the remaining shaft of the stripped fastener. The new igniter went in no problem and I used sheet metal screws to reaffix the unit. From what I've seen on the 'net, cheap fasteners that strip is a common fault on GE appliances.

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

I had read the customers reviews and expected that I'd most likely break the attaching screws. My trick was to not just unscrew then all the way out but to turn it a half a turn and then screw it back in. Then out again a little more then last time and back a little. Didn't break a thing. I did have to move the stove out to get to the plug but that was just enough for me to get my arms in there.

I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.