JBP85WB2WW General Electric Range - Instructions

I ordered a new burner assuming As is turns out: nothing wrong with the burner.

turn off the power at the breaker first

remove the 2 screws under the 'lip' of the stove top (open the oven door to get to them)

prop up the stove top on the cardboard box the part came in

pull off the wires one by one and attach to the new burner OR record where each wire goes first

remove the old burner (2 screws) and attach the new burner

screw down the stove top

try the burner - when it does not work flip the power breaker back on and then try again

bask in the joy, admiration and wonder directed your way by various family members

So easy. Took extra time so the wife would think it was harder. Just read the other reviews for instructions. Didn't have an issue with the wires pulling back into the oven though I did have my "clips" ready.

Used the nut driver to take out the bad motor and installed the new one.

popped the new one on!

I turned the breaker off to the stove and moved it away from the wall. I then removed the center cover off the back of the stove and exposed the wires connected to the bake element. I removed the wires from the bake element and then opened the oven and removed the two bolts holding the element onto the back wall of the oven. I discarded the old element and replaced it with the new first bolting the new in , then connected the two wires and replaced the rear cover. Turned on the power and made a cake.

First unplug the unit from the outlet. Then remove the rear cover, covering the electrical wires. Disconnect the hot /ground wires from the element leads. Then open the oven door and use the nut driver to remove the inner screws to release the bake element. Insert new element and replace all screws and electrical leads. You're all done!

I removed the racks and oven door. I used a socket to remove the screws that secured the element. I pulled the element out to gain access to the wire connectors and used pliers to remove the wires from their connectors to the burned out element. I installed the new element by using the pliers to secure the wire connectors to the element and then installed the element with the socket thus securing the element with the screws.

First I unplugged the stove. Then I removed the two screws inside the oven to remove the heating element. For safety purposes I removed the back panel from the stove also to get a complete view of what I was getting into. That was just 5 more screws and the panel came off and exposed what the heating element was plugged into. Very easy to unplug and reconnect, install the back panel then install the two screws for the heating element and it works just fine.

I went online, found what I thought was the correct part, ordered it, received it--WRONG ELEMENT!
HUBBY phoned parts company, very nice gal helped him find correct element, put new one in the mail to us, and we mailed back the wrong one. We received confirmation via email, and 3 days later installed the proper element. I am back to baking. I bake & mail cookies (55,000 to date) to our deployed troops, so I was lost without my oven! Thanks People!

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Dear PartSelect:

I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.

I simply opened up the cooktop with a screwdriver and disconnected the wires to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.

Matt Brennan

We decided to go "on line" to see if there was any way to fix the stove ourselves and found the Part Select website. After entering the model number for the stove, we were able to find the heating element. We ordered it and received it two days later! We saved money and time. Thank you!

Read posts on this site by others who did the same repair and found that to be a great help especially since the part came with out instructions.
From the posts I was expecting the wires to be short and had vice grips available to stop them from sliding back through the insulation. One still did though. I took off the back plate and pushed it back through. Piece of cake. The clips on the end of the wires were pretty loose and I used some needle nose to crimp them down. I also made sure to unplug the oven prior to starting.

Took two screws out, unplugged the wires.

Put the new heating element in. Plugged in the wires and put the screws back.

Took about 16 minutes !