JCBP66DM1WW General Electric Range - Instructions

The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back panel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.

Removed two screws from the front, two on the back of the control panel. Open the control panel while all the wire were still connected. Disconnected two wires from the old switch. Pull the old switch out. Push the new one into the same opening. Connected two wires to the switch. It is easy and fast.

Very easy to remove the parts and to reassemble

I removed the 4 hex head screws holding the control panel , then the other 4 slotted screws. Disconnected all wires being careful to keep track of the color coding. Had a little trouble with the adhesive holding the face plate( I don't know why they even used it). Put the new panel in and reconnected it. Re set circuit breaker and tried the oven. It still wouldn't heat. it wasn't the control panel, but a burned out wire connecting the element in the back of the oven. Well, anyway I learned how to do the job and the the new panel activates better, so all was not lost.

Removed old racks and replaced with new racks.

Took the oven door off and removed the inner door panel, put new glass assembly part in and reassembled. The hard part was getting the door hinges locked back into place.

Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..

I am a 62 year old woman with NO experience fixing appliances However I didn't have the money for a repairman so I ordered the part and googled "Hiw to change a heating element in a GE range". All the instructions were there and now my oven is working perfectly. I even posted on Facebook for my female friends to encourage them to do repairs themselves. What a GREAT feeling.

Troubleshot the problem, found the SWITCH ROCKER was seized up,
Removed the rear inspection panel, and saw the installation procedure.
Called Part Select and discussed the problem.
Gentleman quickly found the part and we ordered it,
Pulled the existing failed switch out, replace the new switch, done.
Saved at least $100.00 by not having and appliance company do a simple job!
This not the first time Parts Select has satisfied my needs and importance of saving hard earned money.

Sincerely
Satisfied customer
Edward P. Mike

Changed the lower heating element. Simple, simple, simple. I first went on YouTube and watched a couple of videos. Reassurance is a good thing. Okay here we go. 1) Pull the oven out from the wall 2) UNPLUG 3) remove the racks in the oven 4) Unscrew the (2) screws holding the element to the back wall of the oven. 5) There are two (2) connections that you simply pull off. Remove the element. 6) Throw the old heating element away and connect the NEW element where the OLD one was. 7) Put the old screws back in. Plug the oven back in and test. VOILA!!! you are now a repairman.

Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whipping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.

Performed repair using a video for reference.

My exact model number did not appear in the listings, nor were the oven rack measurements clearly stated in items offered. I sent an email to customer service, received an immediate response with the correct answer (re: which part would fit my oven), ordered this item, and had a shipment arrival within days. The racks are a perfect fit, and they look great. The price is less than any other site I investigated.

In this case I had to pull the range out to disconnect the power and also to remove the plate covering the electrical connectors. This was the only way to reconnect the elements terminals since the wires were too short to do it inside the oven. Undo the 2 screws holding the element in place from inside the oven to remove and install the new one before connecting the terminals from the back. Put back the rear cover and reconnect the power.

Watched youtube video. Very easy to replace