JHP98G*Y2 General Electric Range - Instructions

Very easy to replace. Oven works like new again. If you have even the most basic visual and mechanical ability, you will be fine to do this on your own. Total repair time for me was less than 5 minutes. The part was an exact fit!

Took the old one out, measured it, ordered the appropriate size, intalled the new one.

Unplugged oven. Removed the two screws from inside the oven that secured element to the back. I then removed the protective cover for the plug from behind the oven-three screws. Disconnected the element from the electrical wires, removed and replaced the element. And reassembled the cover and all the screws in reverse order. Plugged it in. Presto, 5 mins and works great.

Repair was super easy - read the other stories posted. They give more than adequate instruction.

Amazingly helpful website. Found the part, instructions to install, and able to order in less than 20 minutes!

I first turn off the 220 power braker to the electric stove. Making sure the stove and element is very cool.

I then removed the two screws that hold the lower baking element in place. Pull gently on the element not to break the wires from the wall of the stove (about 3 to 4 inches).

I than unscrewed the right and left wire attached to the element with the nut driver. (This old element was attached with small nut screws. The new one has screws that use a screw driver). Keeping the wires apart, I removed the old element and replace it with the new element part.

In replacing the new element, facing the stove I connected the black wires to the left side (my left hand) and the white wire to the right side (my right hand) with the new screws using a screw driver. REMEMBER TO REPLACE THE WIRES BACK THE WAY THEY CAME OFF WHEN THE STOVE WAS WORKING PROPERTLY. Attach the element back to the stove and turn the breaker on. Easy to do job.

removed 2 screws that hold the element in place, then pulled element out took 2 more screws out and reversed proc. I couldn't have had a better rep to help me find the right part. Thank you

I had a friend of mine who came to my home equipped with screwdrivers and flashlight. After turning off the electricity at the fuse box he removed the oven door (for easier access),removed the screws,pulled out the existing element far enough to disconnect the wires, placed the new one into place, connected the wires, screwed the new one into place
turned the power back on, turned on the oven and after about 15 seconds, the element began to turn from a dark gray to a light color beginning to turn orange.

I was able to slide the stove out from the wall, so it was easier to remove the back cover and disconnect the wiring in back rather than trying to reach into the oven. Then all I had to do was put in the new coil, reconnect the wires and slide the stove back into place.

The new element arrived in just 2 days with normal postage. I followed the simple instructions and was cooking 15 minutes later. It couldn't have been easier. Thanks.

I was very pleased with all the follow up from the time of order until the arrival of the heating element. I have never had the personal communication as I did with your company. The part was ordered on Dec. 26th and arrived on Dec. 29th. Due to the holiday schedule, I did not expect arrival until weeks end. My neighbor installed the heating unit for me and it is doing just fine.

Thank you for the excellent service.

Sherry Shelton

Removed the bracket holding the element, slid out the element, disconnected it from the leads, replaced it with your part and reassembed. Oven now works like new.

1-Shut off the breaker
2-Pulled off the oven door for easier access
3-Unscrewed the old element plate
4-Unscrewed the red and black wires from the old element
5-Screwed on the new element to the wires
6-Replaced the screws on the new element plate
7-Turned the power back on

It only took 15 minutes and a nut driver to replace.The part was $22,well worth keeping my oven going for a few more yaers

Unscrewed the plate and unplugged the old element and plugged the new one in, screwed the plate back on. Done.

First we unplugged stove, if wired into circuit shut off in breaker box. Undo four screws on back cover and detach wires from element. Remove oven door by pulling open and sliding it up off hinges. Undo two screws holding element to back wall of oven. Slide in new element and replace screws in back wall. Replace door. Slide wire leads on new element in back, at this point we plugged range in and tested element to see if heating. It worked so we replaced cover, slide range in and leveled it with wedges. Time for pizza.