JBP30BA1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Betty from Fayetteville, WV
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the center of the element had broken
just pulled the old one out and replaced with new one. very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Cerritos, CA
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stove Burners did not work.
The repair is simple, pull out the old, plug in the new. The most difficult aspect of the repair is to make sure that you have the right part. As this is an old stove, and it was a builder model, the model number did not match exactly, and I got the wrong part which I had to return. Look at the pictures carefully as many of the parts look similar.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Yadkinville, NC
- Parts Used:
- WB07X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
handles broken on oven door
removed old handles and slid door apart align new handles and re-installed new handles. One person job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Boise, ID
- Parts Used:
- WB44X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven began to take too long to bake, temp gauge appeared to be correct heat, but took too long.
I suspected the bottom element was acting up. To repair I first turned off the circuit breaker for the range, confirmed by checking the clock and a burner. I removed 2 1/4" crews using a nut driver, then removed and replaced two Phillips screws, being carful to attach two leads to left side, and one to the right side. Reinstalled the two screws, flipped the breaker and baked some cookies. 100% Success!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Las Vegas, NV
- Parts Used:
- WB07X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broken handle end cap
I removed the two screws in the oven door with a T-15 screwdriver and pulled the inside frame away from the front glass. At which time I hear something came loose it was the oven door spacers, got back on the web site to see were they went from the parts list and put it back together in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from charles city, IA
- Parts Used:
- WB07X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Left oven door bracket broken
You need to remove both ends first you block up under the oven door so it is flat to work on then, you will see inside the door the to sleeves that the long screw goes through is easier to screw back in,you are on the road to finished product. H.l.R
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Linthicum, MD
- Parts Used:
- WB27X10311
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inconsistant oven heating. I tested the sensor and it checked good at room temperature. When I tested it in boiling water and ice water the resistance read lower than it should have. I concluded that thevsensor was the problem. I replaced the sensor but it did not solve the proble. I therefore,
The repair was quite simple. I pulled the range away from the wall. Removved 6 screws from the back panel with a nut driver. I the disconnected the wires from the clock control and then removed the 4 screws securing the control board. I loosened the faceplate from the old control with a hair dryer and removed it with a knife. I afixed the faceplate to the new control with two sided tape. Connected the wires to the new control and secured it with the 4 screws. The only problem one might have is the instructions referenced black and purple wires whereas mine were red and blue respectively. Reattached the back panel with the six screws and plugged the power plug back in. Moved the range back against the wall and tested the oven which tested perfectly. Note please disconnect power before proceeding with the installation of the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Huron, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Winter, WI
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!