JBP30BA1 General Electric Range - Instructions

unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.

Required new light lens for oven this type has five (5) of them; only the oven temp light lens was damaged. Ordered from Parts Select.com received item fast in seven days. removed rear guard plate, than oven temperture switch than slid the neon light switch off of the light lens.Lens is removed from the front panel. Installation is reverse order.

removed old handles and slid door apart align new handles and re-installed new handles. One person job.

I suspected the bottom element was acting up. To repair I first turned off the circuit breaker for the range, confirmed by checking the clock and a burner. I removed 2 1/4" crews using a nut driver, then removed and replaced two Phillips screws, being carful to attach two leads to left side, and one to the right side. Reinstalled the two screws, flipped the breaker and baked some cookies. 100% Success!

The repair was quite simple. I pulled the range away from the wall. Removved 6 screws from the back panel with a nut driver. I the disconnected the wires from the clock control and then removed the 4 screws securing the control board. I loosened the faceplate from the old control with a hair dryer and removed it with a knife. I afixed the faceplate to the new control with two sided tape. Connected the wires to the new control and secured it with the 4 screws. The only problem one might have is the instructions referenced black and purple wires whereas mine were red and blue respectively. Reattached the back panel with the six screws and plugged the power plug back in. Moved the range back against the wall and tested the oven which tested perfectly. Note please disconnect power before proceeding with the installation of the new part.

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

The repair was easy except what caused it to break .Their was a missing screw on the door itself that was never put on or came off could not find old screw,once it was replaced new part was stronger than before.

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.

I removed the two screws in the oven door with a T-15 screwdriver and pulled the inside frame away from the front glass. At which time I hear something came loose it was the oven door spacers, got back on the web site to see were they went from the parts list and put it back together in no time.

You need to remove both ends first you block up under the oven door so it is flat to work on then, you will see inside the door the to sleeves that the long screw goes through is easier to screw back in,you are on the road to finished product. H.l.R

Moved the range out and disconnected the power cord. Removed the back cover.Disconnected wires after labeling the them. Removed the unit from the range,Carefully removed the front decal and applied to the new unit. Installed the new unit into range and wired according to the instruction and put the covers back on. plugged back in and tested the range and everything functioned correctly.

I disassembled parts and panels from the oven door as needed to remove the handle end caps. It was not clear to me what the best disassembly method was, because I used a different method when assessing the problem as when I performed the actual part replacement. The quickest way is to take the top two screws on the inside oven panel loose, but leave them in their retainers. Remove the side trim screws on the plastic upper side pieces. Remove the four sheet metal screws on the bottom of the door, located the far right and left (two on each side). Carefully split the inner and outer oven panels to access the mounting screws for the oven handle. Replace the oven handle and reverse the disassembly process.

The repair is simple, pull out the old, plug in the new. The most difficult aspect of the repair is to make sure that you have the right part. As this is an old stove, and it was a builder model, the model number did not match exactly, and I got the wrong part which I had to return. Look at the pictures carefully as many of the parts look similar.

It wasn't so much the repair that was needed as how impressed I was with the fast delivery. Without a fourth burner & a holiday weekend coming up I was in desperate need of my element. I ordered it around 1:00 pm on a friday & it was delivered the next day before noon! Very impressed with the ease of ordering & receiving. Thanks again.