JGB910BEC2BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DAPHNE from CHICAGO, IL
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
while cleaning I broke the tubes either lifting or closing the top.
I bent the tubes very slghtly to rech the area of attachment. I first screwed them with my hand then tightened them with an adjstable wrench. It was really simple and fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SOUTHBURY, CT
- Parts Used:
- WB20T10024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Temp probe was defective
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from LEEDS, AL
- Parts Used:
- WB01K10112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudene from ORCUTT, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks old and ugly
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILL from SOMERSET, NJ
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
the tubes both leaked
replacement was a snap and took only a small adjustable wrench and a flashlight. asome slight bending of the tube was required, but a gentle hand solved the problem easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LEAH from YUMA, AZ
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
tube that sends gas to burners broke both left and right front this happen due to opening the range hood to clean inside
I turn gas off to the appliance then I remove the old gas lines and installed the new ones. I did find it easlier to attach the line at the burner knob first then attach it to the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Woodstock, IL
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Front burners had to be lit with lighter
My son lifted up cooktop, unscrewed the front plate to gain access to old tube burners, removed and replaced with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from GAINESVILLE, GA
- Parts Used:
- WB16K10070, WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Bloomingdale, IL
- Parts Used:
- WB27K10059
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Control panel not working
Very easy, took screws ofrf back of top unit, pulled plugs off and changed out. Works fine, also this website $100 cheaper for this part than website GE connected me to, and the other site said part on National back order. Promply shipped, received in 2 Business days
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from The Villages, FL
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
burners would not light
Remove the old tubes. Lift the lid NO MORE THAN FOUR INCHES. !!!!! Feel for the connections on the switch ends and attach losely. Carefully ( with some slight bending ) attach tubes to the burners. Tighten all connections. Do not over tighten.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Ashland, MA
- Parts Used:
- WB29K10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn and pitted burner caps
Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tucson, AZ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Probe Sensor
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from Jacksonville Beach, FL
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Open door. Put racks in.
nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Ogdensburg, NY
- Parts Used:
- WB16K10055, WB29K10001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stain/polyurethane dried on burner head & cap
Lifted both pieces off and placed the new ones on,turned on the burner and it worked as it should.
Was this instruction helpful to you?
Thank you for voting!