PGS975DEP3WW General Electric Range - Instructions

pulled out appl,removed door,racks,lifted oven bottom to remove,removed both oven and broiler ignitors---went to back of appl to remove gas control valve and replaced--used old oven ignitor in broiler(took chance it would work-it did!)installed new ignitor in oven--tested perfectly--point of info if you have an oversize or dancing flame in oven or broiler--remove flame tube and with 1/2 inch open wrench tighten orfice all the way until it stops--don't force or over tighten-- (the air shutter should open all the way)--flame should be about an 1 inch with white tips--adjust as needed-overall repair including adjustments took about an hour-hope this helps--and i'm not a professional repairman

Odered igniter from part select, it arrived the next day. Removed oven door removed heat shield on bottom of oven and there it was. Removed the two screws pulled the wires till the connector came through, unpluged connector, plugged in new igniter, repaced everything and Bam, we were cooking. Did not even have to pull oven out from the wall. Super easy.

plug in thermistor when needed

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

No response from GE website (very disappointing). google "repair GE gas range igniter" and very simple step-by-step instructions...apparently is very common with GE appliances...even mine that was less than 14 months old. Service tech would have charged $300. Did it myself for $80

I had read the customers reviews and expected that I'd most likely break the attaching screws. My trick was to not just unscrew then all the way out but to turn it a half a turn and then screw it back in. Then out again a little more then last time and back a little. Didn't break a thing. I did have to move the stove out to get to the plug but that was just enough for me to get my arms in there.

Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect

put it in but it keeps falling out. they're made narrower than my oven grate.

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.

Owners manual provided no help. Thankfully, the internet did. Internet convinced me the problem was the igniter, and with hindsight that was correct. 30 mins on the net to troubleshoot. On my model, the oven door must be removed to remove the bottom splash shield. Internet to the rescue to show how to remove the oven door. 10 minutes on the 'net, 30 seconds to remove door. Heat shield came out in about a minute. First machine screw that secures the igniter to mounting bracket out in 45 seconds. Second machine screw stripped in two wrench turns. Since the location of the mounting bracket was a cramped space (in a "well"), had to hand hold a hacksaw blade to cut off the head of the stripped machine screw. With only 3/4" of possible travel, this took 90 minutes. Then drill out the remaining shaft of the stripped fastener. The new igniter went in no problem and I used sheet metal screws to reaffix the unit. From what I've seen on the 'net, cheap fasteners that strip is a common fault on GE appliances.

remove oven door of course you cut gas and power off first tried to get screws out of igniter the heads broke off had to take cover off to get screws out slide range out of cabinet take back off to unplug igniter then reassemble

Easy to install replacement parts using the screws provided.