JBP35DIM6WW General Electric Range - Instructions

Removed door from range(see manual for instructions). Set door face down on protective cloth material .Remove two top screwws, 3 bottom screws and lift back of door off. Remove two screws on each side of door bottom channel and remove channel. Put in new trim on bottom of glass window and put screws back in. Set back of door on top of front cover and screw two top screws and 3 bottom screws back in. Set door back into range. Lock clips on both hinges.

Replaced Electronic Control Board. Very easy to do with a nut driver and a screw driver to remove the old one. You may need a pair of needle nose pliers to remove Connector TB100 and TB101. Just squeeze the bottom of tabs to release connector. I also found that in the process of removing the Control Board label that it may rip in certain areas even while using a razor blade, so be prepared to purchase a craft paint brush and craft white paint to touch up the back of the label. It took 2 coats but looks like new..

The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.

I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair actions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!

Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.

Took back off and replaced.

Removed torx screws for door handle as well as torx screws for both hinges to separate the door halves to extract broken glass and to install new glass panel. Other reviews said not to remove hinge screws, however I had no problem reinstalling them.

The part was exactly what we needed. However, we didn't find the video online to show how to replace the part until we were almost finished. (https://www.youtube.com/watch?v=ovwcJhfWHXQ) If we had found the video, it would have saved us a lot of time because we undid more of the door than we needed to. Also, the video tells you exactly what size tools to use. However, taking the door more apart allowed us to clean more of the inside of the door. So, watch the video before you start, and also, be prepared to spend time cleaning the insides of the door. Also, when we put the door back together, we accidentally turned the front glass panel of the door upside down and it wasn't noticeable until we had put the door back on the oven. So, we had to take it apart again to fix it. All said, we're very happy with the new part. Thank you PartSelect!

I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.

First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.

popped out the remainder of old lens, then pushed in new ones and slipped on plugs.

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

We purchased a completely black range then my wife disliked the rangetop being black so I ordered a white replacement she loves it. It was so easy to replace. Very pleased.

Luckily I retained the original manual and was able to order the drip pans through your company from the original manufacturer. Be sure range is turned off, lift the burner locking element, then lift the burner a bit. Remove the burner by pulling it, disconnecting it through the opening in the drip pan. Lift out the old drip pan and replace it with the new one. Then reconnect the burner through the opening in the drip pan. Press the burner locking element in place and the job is done

1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.