Models > PGS975DEP2WW > Instructions

PGS975DEP2WW General Electric Range - Instructions

Jump to:

All Instructions for the PGS975DEP2WW
61 - 75 of 161
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
DANIEL from STAMFORD, NY
Parts Used:
WB49X29679
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
OVEN LIGHT OUT
REMOVED 2 SCREWS AND LOWERED LIGHT ASSEMBLY. UNPLUGGED THE OLD ONE, AND REPLACED IT WITH THE ITEM SENT TO ME
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Terry L from Puyallup, WA
Parts Used:
WB02T10461
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Rubber Grate foot worn or missing.
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Stratham, NH
Parts Used:
WB02T10461
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
feet keep falling off
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.

I do use silicone to help hold the foot but it still won't hold
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jesse from Knob Noster, MO
Parts Used:
WB02X33180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Broken rear drawer support
Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from HENDERSONVLLE, NC
Parts Used:
WB02T10461
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Rubber grate foot failed
Cut off approx. 1/8" in length for correct fit.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
NICK from Vernon, CA
Parts Used:
WB48T10068
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Plastic guide Broken
replaced Plastic Guides
9 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dock from Aurora, CO
Parts Used:
WB02X33180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
The storage drawer came without supports.
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
robert from FAIRFIELD, OH
Parts Used:
WB20T10024
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Oven meat probe broken
This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mohammad from BARTLETT, IL
Parts Used:
WB16K10055, WB16T10046
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The old burners were damaged by the prior owners.
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from SOUTH ELGIN, IL
Parts Used:
WB16T10046, WB16K10055
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Burners wouldn't light
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eric from SOUTHBURY, CT
Parts Used:
WB20T10024
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Temp probe was defective
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from New York, NY
Parts Used:
WB13T10045
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
Replace the lower oven gas igniter
Flip toggles to release the oven door. Pull up on oven door to remove. Put door aside. Lift enamel bottom. Slide strait out. Remove aluminum shielding from around the igniter. Loosen igniter, unplug the igniter. Remove burner cowling. Plug in new igniter. Attach cowling to new igniter. Screw it all back in place. Stuff wiring connected back through the protective hole. Depress close door button and test. It takes about 10-15 seconds to ignite. Reinstall aluminum protector. Re install bottom enamel piece. Carfully slide oven door back on pegs and flip toggles to lock. Have a big glass of water and yell, Honey I fixed the oven!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dana from LEEDS, AL
Parts Used:
WB01K10112
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sarah from MONTGOMERY, TX
Parts Used:
WB04T10050
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Followed a GE Video on installation
Followed GE repair video
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
BOB from BURBANK, CA
Parts Used:
WB13T10045
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
GAS OVEN WOULD NOT HEAT - NO FLAME AT BURNER
Could not have been easier. All screws are 1/4 inch. Oven door can be removed to make it easier to get to screws in back of oven,but igniter can be installed with door in place. Remove bottom panel then remove four screws on flame spreader. Remove trwo screws that hold igniter in place. Replace with new igniter, it may be necessary to remove the clip on new igniter and splice the two leads. Now your cooking with gas.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the PGS975DEP2WW
61 - 75 of 161