JGSP28SEN1SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- fred from PALM COAST, FL
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shortage in wiring cause the housing to burn out
Replaced new light housing.
Thanks to you guys for the prompt response
Thanks to you guys for the prompt response
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from las vegas, NV
- Parts Used:
- WB13X46909
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Sparking at 2 different burners all by themselves
Replaced Spark Module and adjusted igniters
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from New York, NY
- Parts Used:
- WB13T10045
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Replace the lower oven gas igniter
Flip toggles to release the oven door. Pull up on oven door to remove. Put door aside. Lift enamel bottom. Slide strait out. Remove aluminum shielding from around the igniter. Loosen igniter, unplug the igniter. Remove burner cowling. Plug in new igniter. Attach cowling to new igniter. Screw it all back in place. Stuff wiring connected back through the protective hole. Depress close door button and test. It takes about 10-15 seconds to ignite. Reinstall aluminum protector. Re install bottom enamel piece. Carfully slide oven door back on pegs and flip toggles to lock. Have a big glass of water and yell, Honey I fixed the oven!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenn from FORT WORTH, TX
- Parts Used:
- WB13T10045
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
bake cycle would not work
open the oven door (remove) ,disassemble the igniter ,replace the igniter .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Ashland, MA
- Parts Used:
- WB29K10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn and pitted burner caps
Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from GAINESVILLE, GA
- Parts Used:
- WB16K10070, WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from CYPRESS, TX
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very easy
there were no grate pads so it was easy to add them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Broadalbin, NY
- Parts Used:
- WB02T10461
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
The Grate foot is to big for the hole.
I had to drill the hole to a larger size to enable the foot to fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Homosassa, FL
- Parts Used:
- WB02X33180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven will not heat
As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chelagh from Fredericksburg, VA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
Nothing technical.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Tijeras, NM
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate foot bdroke off allowing grate to scratch cooktop
Used scribe to remove grate foot plug still in grate inserted new foot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Paris, TN
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
F2 error when oven was heating up, along with a beeping noise and then it shut off
Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Long Beach, NY
- Parts Used:
- WB13K10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
To Replace Gas And Burner Parts In Section 4
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete
Was this instruction helpful to you?
Thank you for voting!