JGBP85SEM3SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Andrew from SEATTLE, WA
- Parts Used:
- WB28K10212
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
The old surface burner orifice tube was accidental twisted
This surface burner is generically made for multiple manufacturer's stoves so the gas tip does not align with this model precisely. In order to make the gas tip aligns, one needs to bend the aluminum tube to an angle where it would fit to the stove housing or otherwise the gas outlet would not release the gas exactly to the right spot. This requires using either a professional aluminum bending tool or we will need to manually bend the tube slightly without causing kinking on the tube. Putting kinking on the tube would cause blockage of gas. I think your website should publish this so whoever buying this would know the risk as aluminum is a very soft metal and you can easily wreck the tube wasting the time and money. Other than that, the item works quite well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Sheboygan, WI
- Parts Used:
- WB35X29668
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Oven door gasket was damaged and leaking
I watched the repair video on YouTube and followed his instructions as much as possible. Went pretty well as I thought it would be harder. I’m pretty handy so, I was pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from ST AUGUSTINE, FL
- Parts Used:
- WB29K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner cap replacement
I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time.
Otherwise everything was great!
Otherwise everything was great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlie from NAPLES, FL
- Parts Used:
- WB35X37973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom badly marred after 16 years.
Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond J. from EASTPORT, NY
- Parts Used:
- WB16K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
flame was inconsistent. too much air.
replaced old with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from ANDOVER, OH
- Parts Used:
- WB04K10021
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber cracked
Took 5 minutes to repair easy peasy??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudene from ORCUTT, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks old and ugly
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from FLAGSTAFF, AZ
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven wouldn't light
Remove interior bottom of oven, remove igniter screws, unplug igniter. reinstall igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from EL SOBRANTE, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Gas Range oven not heating/replaced new heating element
Removed oven shelves, removed lower cover, removed heating element, removed lower drawer and unplugged element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dottie from SAN DIEGO, CA
- Parts Used:
- WB03K10216
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken range knob
placed on range
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from rohnert park, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
igniter wouldn.t work
had to take back off of oven because of the connector and the plug end insert had the wrong pin so i had to take it apart and use old ones then i put the assembly in /and put oven back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fawn from MEREDITH, NH
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Ignitor would glow at orange but not white. Not enough heat to open valve to let gas run
Got the general idea off a u-tube video. Very simple and would have been even easier had I used a 1/4 in nutdriver instead of socket. Removed 2 screws (flathead) on the lower cover of oven. Removed 1 nut holding shield. Removed 1 nut holding protective trap door on rear, pulled coupling through hole and disconnected. Removed 2 nuts holding ignitor. That's it. Replace everything in sequence and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Brooklyn, NY
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would Not Stay Lit/Smell Of Gas
The repair was pretty straight forward. I simply removed the old igniter, then I snipped the wires. Using the included wire nuts I spliced the old wires with the new. The longest time was spent looking for my wire strippers. I must say that the customer service was very quick and responsive. I received the part but it was broken. One call to customer service and the new part arrived the next day. Great job!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!