JCSP46DP2BB General Electric Range - Instructions

turned off power to oven; pulled out old bulb (unscrewed glass cover to access). Noted the direction of the electrical prongs when pulled bulb out... and inserted new bulb. Turned back on power to oven - bulb worked

pull out stove, unbolt old temp sensor inside stove with 1/4 nutdriver, go to back of stove and take off cover and unhook sensor and hook up new one, put all back together and slide stove back in place.

Remove and unplug the control panel. Remove four 1/4 in screws securing the metal panel to which the four rangetop controls are mounted. Unscrew the affected control, be careful to note the wiring layout on the control. Reassemble and test test out all functions.

I'm well past ninety and my sweet daughter inserted the tiny prongs. I was delighted to find a place that had the bulbs. Thank goodness for the internet ! (I'm not too old for that)

Use screwdriver to pull down tab on both hinges. Good hind on door and as you lower to full open door will come off. Pull old bottom, insert new bottom and put door back in slots. Close and then reopen to first position and push tabs back up to lock position

I checked various sites on the net and decided that the temperature sensor was the problem. The GE price for the replacement part was about $105, most of the other sites offered the sensor in the $70 range. PartSelect $12.95 When the part arrived, I removed a small self taping screw, pulled the high temperature wire connector into the oven space, disconnected the quick disconnect fitting, attached the new temperature sensor, pushed the connecting wire into its hole, replaced the screw and that was it. I probably saved about $200 in parts and labor over what a local repairman would have charged. Oh yes!! I first disconnected the power at the breaker box. Very important.

Just note the wire colors and match them where they go on the new control, remove and replace 7 screws and a zip tie and I was done.

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

1st replacement part was damaged from Shipping.
Parts Select sent a new one that i received in only a few days.
our stove is slid into a granite island so the disassembly was not as simple as most. It was necessary to remove the controls, the controls housing & screws along the top of the oven door.
Within an hour the stove was back in place and working perfectly.
Great service from Parts Select

recieved part the next day. looked different but I followed instructions and the part worked perfect.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

The thry was rusty I took the door out And i slide out the thry it's take five minutes I did it by myself now my oven Look like a new I'm so happy now I get the part quickly thank you

REMOVED 2 SCREWS AND LOWERED LIGHT ASSEMBLY. UNPLUGGED THE OLD ONE, AND REPLACED IT WITH THE ITEM SENT TO ME

1) Shut off power to oven
2) Removed oven door using snap down hinges on door
3) Removed 4-phillips head screws holding the oven frame to cabinets
4) Pulled oven out of cabinet and set it on stool in front of opening
5) Remove 2-hex screws holding metal shield covering the electrical wiring on back of oven
6) Unplugged bad thermostat connector
7) Removed the single hex screw holding thermostat inside the oven
8) Pulled the thermostat and lead wire from oven
9) Fed the new thermostat wire into inside back of oven
10) Reverse steps 1-7