JB680DP2WW General Electric Range - Instructions

Wait until oven is cold. Turn off power to the oven at the breaker panel (confirm: clock will be off). Open oven door. Remove upper rack. Unscrew glass cover over lamp and socket (it only turns one direction and may be tight). Slide cover off lamp socket. Remove old lamp - pull straight down. Install replacement lamp. Lamp pins line up front to back. Do not touch the lamp - use latex gloves. Make sure the lamp is fully pushed into its socket. Replace the glass cover by centering it on the socket with glass retaining tabs close to the matching areas on the metal socket. Take care not to damage the lamp. Turn the cover to lock in place. Make sure it is locked. Replace oven rack. Turn the power back on.

Pull the old one put in the new one ... took about 20 minutes

Removed back panel screws, removed back panel, removed screws of the control board, remove control board, heated glue and tore off plastic face plate, placed face plate on new control board, installed new control board, moved wires from old control board to new control board, test out oven, reinstalled back panel

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

The repair took Less than 20 Mins. So easy anyone that is handy should be able to do this with ease. And PartSelect is great to order from Order was placed on a Weekend and order was at my home on Tues! Thats a one day shipping and it was a ground shipment!!! Great Job PartSelect!!!!!! Mark

Tried GE onoine parts department first and ordered the wrong part, then tried the customer hotline and they referred me to the right part but didn't explain that the design had been modified (the drawings had not been updated). I found an explanation on Part Select AND the parts were cheaper. Part Select sent the part, the necessary screw, and an appropriate instruction manual. Each support took less than a minute to screw in with a socket wrench.

Some of the original TO-9 switches were fused by the heat. I made them functional again with a cutter on a rotary tool, but to make the repair properly, I ordered the new control unit and the faceplate graphics. Note the guide tabs at the bottom and right edges when replacing the graphics. Don't plan on reusing your old graphics (unless you are a wizard at removing the very strong adhesive).
To gain access to the part, remove the 2 screws (part 715) in the bottom of the control assembly with a stubby screwdriver. Using a nut driver, remove the two screws (part 1000) on the back at the corners, being careful not to drop them behind the oven. Pull out at the bottom, then move the whole unit toward you. Note the position of the wires. A digital photo can help here. Remove the wiring and 4 screws holding the clear plastic TO-9. Put the screws in the new unit in the same holes and rewire. Put the assembly in place top-first and align the screw holes. Finding the same thread placement for the lower screws can be tricky, so start them gently.

1. Pulled the stove out about 6-8 inches. 2. Opened oven door and removed 2 screws to free up stove top. 3. Lifted stove top to access another panel. 4. Removed about 6 screws allowing removal of sheet metal cover above Latch/lever mechanism. 5. Removed 2 screws at top center "boiler plate" to allow removal of Latch/Lever mechanism. 6. Slipped off electrical connector from microswitch mounted on Latch/Lever mechanism. 7. Then removed old mechanism 8. Set new mechanism in place, re-attaching electrical connector onto microswitch. 9. Then with my finger, I bored down a few inches through the insulation to make sure the base of the new Latch/Lever mechanism was in contact with the oven at the base of the insulation. 10. I replaced the 2 screws at the top center "boiler plate." 11. I reattached the sheet metal cover with 6 screws, making sure holes were lining up. 12. Finally, I lowered the stove top and reattached the remaining 2 screws that secure the stove top. It was all pretty easy, but I did not see a prop (like some models have) that would hold up the stove top while performing the unscrewing, screwing, removing, replacing, etc., so I used a piece of wood to rest the stove top on, and lifted it with my left hand while I did the "operation" with my right hand.

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...

Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.

Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.

loosen interior panel of oven with star driver. Removed broken arm. install inner screw and then install final screw to both panels and handle.

The inner screw mount only through the exterior door only making it tricky to line up the final bolt which goes through both panels and the handle.

Other than that it when smoothly.

Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.

I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it complete.