J765*03 General Electric Range - Instructions

Made sure oven was turned off. I used nut driver to remove nuts holding old element to back of oven. gently pulled element out of wall, taking care not to yank because of wires attached to back of element. Made sure oven was off again and then used nut driver to carefully remove wire leads from receptors on element. removed old element from oven and got the new element. carefully used nut driver to attach wire leads to new element. When snugging the bolts to leads, used pliers to keep leads on the element from bending. carefully replaced wires and rear of element into the space behind oven, and used nut driver to attach the back of element to the back of oven. shut oven and turned on to make sure it worked. it did. I was very pleased with my experience with part select dot com, and will be buying another element soon to replace the one in my other oven! Thank you

The part was delivered in 24 hours with regular
shipping and was simple to replace. Uncrewed
it, disconnected wires from the old one and connected
the new one. Cost a little more than $30 including shipping and the oven works great!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Removed the old piece and connected the wires to the new piece. I'm a woman and this took me less that 15 minutes to complete. Easy as pie. On top of that, I received my order within 3 days! Very impressive, PartSelect. Thanks.

Ordered part, took old bake element out, installed new bake element. It was real easy.

At 76 I no longer do my repairs so I asked my daughter's friend to do it for me.

took old element out , put new element in.very easy.

First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire connection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.

Drilled out the screw on one wire as it was corroded to the metal socket. Sanded both wire terminations. Installed wires into terminal block. Reassembled all loose parts and installed into burner slot. Worked perfectly.

Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to test it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*

Turned off power. Removed old broken one installed new one in minutes. Turned power on and tested it out. If this 60 something lady can do it, you can too.

I removed the oven door and racks. After turning off the power I raised the old element up to be able to access the screws. I undid the two that connected the element to the back of the oven. After pulling the element forward, I undid the two screws that supplied power. I reconnected everything and, after turning the power back on, tested the element. It worked perfectly. It has been used quite extensively since then with no problems.

First I removed two hex nuts holding the element's faceplate to the back of the oven and pulled the entire element straight toward me a couple of inches, pulling the element's ends and connections into view. I unscrewed the two screws holding the element ends to their connections, connected the new element, pushed it back in place, and screwed the faceplate tight again. The most challenging part of the whole process was finding the part number for the GE oven (it's on the frame of the storage drawer underneath the stove).

My husband removed the two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires. He then removed the old bake unit and replaced it with the new one. He reattached the wires and pushed the element into place. Then he put the two screws back in that hold the element in place.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Removed the element and replaced with the new. Reattaching the wires and securing the new element back in place with the screws provided. Packed well, shipped promptly, installed quickly. Super easy.
Thank you.

This was extremely easy to replace. When I told my mom I would replace it for her, she thought I was crazy. When she saw how easy it was, she finally understood. I had to remove the two screws holding the element in place. I pulled it out about 3 inches and unscrewed one screw for one wire. I didn't want to lose the wire, so I immediately connected the wire to the new element. I disconnected the second wire and attached it to the new bake element. Then attached the two screws putting the plate back up, securing the element. So easy! Just unscrewing and replacing 4 screws and I was done!! Took less than 10 minutes. I didn't have any real tools available, so I used a small adjustable wrench and it worked fine. The best part was it was so easy we were able to have a working oven in time for Thanksgiving!