P2B918DEM1CC General Electric Range - Instructions

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

ordered over the phone a new temp sensor. Un plug the oven, take off the back, open oven and unscrew the temp sensor, pull the sensor until the elec connector clip comes through so you can unclip the old sensor, clip on the new then pull the line back and re attach the sensor to the ovn. Plug in the oven.
Pretty simple, just hard to work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.

Very was ti replace racks and knobs. Very fast mail service

less then ten minutes, used a electric screw driver and in a snap, finished, I always buy my parts on line at parts select my stove is old but in good condition except parts give out sometimes and I just order part and keep on cooking.

replaced lights in refrigirator and freezer

PLEASE BE ADVISED WHEN THEY SHIPPED THE BACK ORDER 1 -(taupe) LARGE CAP - RECEIVED 4 BLACK CAPS - 1-SMALL
2-MEDIUM 1-LARGE (ALL BLACK) - STILL LOOKING FOR
A LARGE CAP IN taupe color!

Received refund for 1-large cap
PROBLEM IS ALL OTHER PARTS ON THE GAS STOVE
ARE taupe in color - do not want black!

your advice?

Gasket front door frame off with old and on with new 10 Mins.
Gasket Assembly door takes time first need to remove the oven door need to lift up enough to clear oven door upright catches be careful door is heavy my need another person with lifting and lay the door on a flat surface like a table and they're a lot of screws to be undone remember were the go when reinstalling do not rush take your time do to you are working with sharp edges time 4 hours for remove door take apart but together and reinstall

I merely replaced the old caps with the new ones. It couldn't have been easier!

Remove the existing burner and install the replacement.

I watched the repair video on YouTube and followed his instructions as much as possible. Went pretty well as I thought it would be harder. I’m pretty handy so, I was pleased.

Pull out wires & replace element by putting wires back in then tighten...done!!!!

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Took 5 minutes to repair easy peasy??

Used nut driver and removed the 4 nuts holding the broiler. Pulled electrical wires of old broiler Received new unit and it was just as easy to replace. Thank you for assistance.