JGS968KH6CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from Salem, OR
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Flashing F2 and erratic temperature readings.
Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Woodinville, WA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our bottom drawer support broke and the bottom drawer was canted
Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from San Diego, CA
- Parts Used:
- WB13T10045, WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broiler and Burners would light, oven would not light and you could smell gas, also before the oven stopped working the oven was taking awhile before it would light
1.Removed the oven door. 2. Removed the oven floor panel ( slides right out ). 3. Removed cover plate and and removed one screw holding the igniter in place. 4 was able to pull the wire into the oven and unplug the igniter. Ordered a oven temp sensor but never needed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Cave Creek, AZ
- Parts Used:
- WB41T10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
defective oven door seal
pull out defective seal with pliers clean area and press new seal into place making sure the spring clips on seal are completely inserted into door slots push ends of seal into holes in bottom of door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Shakopee, MN
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Stove drawer rear guides broken
Installed new guides with a nut driver without any problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Newark, DE
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Range lower drawer would not stay on track.
Easy to install replacement parts using the screws provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from Deer Park, WA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken drawer support
Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John R from Asheville, NC
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing meat thermistor
plug in thermistor when needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Stuart, VA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic slide for storage drawer broken.
Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Munt Laurel, NJ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Probe broke
Ordered new probe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Kenner, LA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate Foot Have 8 For My Stove And One Breaks Every Now And Then
This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara J from Sweetwater, TX
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Missing grate foot.
Ordered by phone parts & very pleased with all of transaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from RICHMOND, VA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
rear drawer supports broke
Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gino from glen ellyn, IL
- Parts Used:
- WB13T10045
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
faulty igniter
No response from GE website (very disappointing). google "repair GE gas range igniter" and very simple step-by-step instructions...apparently is very common with GE appliances...even mine that was less than 14 months old. Service tech would have charged $300. Did it myself for $80
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vaughn from Visalia, CA
- Parts Used:
- WB13T10045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Stove top worked, Broiler worked, but Oven would not heat
Odered igniter from part select, it arrived the next day. Removed oven door removed heat shield on bottom of oven and there it was. Removed the two screws pulled the wires till the connector came through, unpluged connector, plugged in new igniter, repaced everything and Bam, we were cooking. Did not even have to pull oven out from the wall. Super easy.
Was this instruction helpful to you?
Thank you for voting!