JMP28BA1AD General Electric Range - Instructions

My husband (a retired tool & die maker) easily removed the old bake element after first turning off the circuit. He cleaned up the burned salt that we had used to try to put the "fire" out but finally just shut down the circuit. Then just as easily istalled the new element. Thanks to your quick service, we were only without the use of the oven for a day and a half!

I should note that my first order to PartsSelect.com
was made on-line and that I selected the wrong part by comparing the burned-out element to the web site picture. When I received that part, I phoned and quickly corrected my mistake, ordered the correct part and obtained return instructions.

With the correct part in hand, I removed the two screws holding the element in place, pulled the element out a short distance to disconnect the two wires and removed the burned-out element. Reversing this procedure I installed the new bake element and completed the job by checking out the oven heating. The hardest part of all this was reaching over the oven door and stretching to unscrew and screw the necessary screws.

I had to remove two screws that held these elements in place from back of oven; pull the elements out about three inches to disconnect two wires; connected wires to new elements and
replaced two screws.

A very easy job to perform thanks to right parts from PartSelect.

- removed the old element
- looked for part number, was none
- could not find direct replacement listed
- compared to dimensions on drawing
- ordered part
- discovered that the mounting plate on new element was too small, holes did not line up, did not cover opening in back of oven.
- sawed off mounting plate on new element
- removed mounting plate from old element
-drilled out holes on old mounting plate to accept new element
- attached the modified element
- Everything works fine.

By myself

Followed the instructions

I spent half an hour finding my driver set. It took about 25 minutes to turn the power off, remove the racks and element and replace the new elements.

.Received the part promptly. Installed it in about 30 minutes. With appliance servicemen, I figure I saved about $200.00 doing it myself. Thanks

removed two screws disconnected old element from the two wires and replaced it with the new element. It saved $60.00 service call.

I had to struggle to get the pliers to grab hold of the screw because they were so tight. I was worried about "stripping the screws" but finally they loosened and I got them both out. My friend was holding the flashlight, so that helped. I was not real sure what to do next but the wires popped off the element so it was clear that all I had to do was pop the new one on. Easy. I had the most trouble trying to get the screws out. I saved myself $$$. Thanks for your help in sending the correct part!

My son took care of removing the broken parts, opening the door and replacing the new handle ends and then finished! It was easy watching him do the work!!!

It was easy except that I had to make just a small modification to the electrical connection (holes were to small). . . . Other than that, its was a breeze to install.

Dislodged screws to oven door to get to handle assembly. Fairly easy, however, new door handle end caps do not come with screws and the old screws were not a good fit. Almost stripped the old screw trying to get it in place. Strongly suggest that Part Select send replacement screws with handle to facilitate repair. Door handle is back up but is now loose until I can find/secure appropriate replacement screws and repeat the process all over again.

First I made sure I turned off the breakers in the circuit box that controlled the circuits for the ovens . Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The factory wrapped a large amount of tape around the connection between the wires and the heating element. That took a while to get off. And I searched for heat-resistant electric tape to replace it (because, it must have served some purpose if they had it on originally). The wires hooked onto the spade connectors for the new elements with no problem. I pushed them back into the hole in the back of the oven, replaced the screws, turned the breakers back on, and it worked great from there on.

Repair was very easy-make sure you shut the electricity off at the breaker box-having the oven control off does not kill the electricty to the element . Removed the screws, pull out the element, disconnected two wires, re-attach to the new element, install the screws.