JMP28BA1AD General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- maria from great neck, NY
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
a segment of the broil element took on fire
it was real easy, I just watched my husband do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donnie from SAN ANTONIO, FL
- Parts Used:
- WB15K5068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Oven door handle broke
Removed 2 torx screws from enter oven skin then Removed 4 quarter hex head screws to remove handle and installed in reverse and the people at partselect were nice and the parts came quickly. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HOUSTON, TX
- Parts Used:
- WB17X210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old Terminal Block was arcing.
Cut Wires to old terminal block and wired in new Terminal Block
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- hollis from Clarksville, MD
- Parts Used:
- WB44K5013
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
The broil element broke.
We removed the two very tiny screws that held the plate through which the element was connected to the wiring. It was extremely difficult to do so, because the screws were so tiny. Our socket set did not have such a small attachment, and we had to use an adjustable wrench. Once we accomplished that, we unhooked the old broil element from the wires. At that point, the wires snapped back into the wall. There was almost no slack to pull the wires back out into the oven so that we could hook the new broil element up. It took more than an hour of maneuvering before we were able to get hold of enough of the wires so that we could grab onto each one and hook up the new broil element. One we did that, it was easy to place the broil element back into its brackets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Mountain View, CA
- Parts Used:
- WB30M2
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Shorted out the burner... fat gets into the receptors on these old stoves.
The only hard part about putting in a new terminal block (and this time I had to replace the burner too, because that fried too) is stripping the stove wires, because that thermal insulation is very hard to get off. Otherwise, it's simple. In this case, I had already replaced this one (sigh), so had already cut & stripped the wires, so it was all easy. Frankly, the sane thing to do is buy a new stove, but wife is too cheap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- deborah from poughquag, NY
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnrd -out heating elements
Turned AC off. Removed bracket screws and pulled out ac connections. Removed old element and reilstalled new element and set AC on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Rowlett, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner worked intermittently
Lined up the prongs and slid it right in, took 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WEST WARWICK, RI
- Parts Used:
- WB30M1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
a plug on the element broke off while cleaning and replacing
Absolutely no tools required for this task. Simply align the prongs to the female portion on the stove top. Carefully push in until the element is in place then line up with the drip pan slot. No instructions are necessary!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from BLUFFTON, SC
- Parts Used:
- WB30M1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken heating element
remove broken heating element and install the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PROVO, UT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls were badly tarnished . . . shine could not be restored.
1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod unit and bowl into the hole in the range top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Garden City, ID
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed New Burner Bowls
Removed the old burner bowls, replacing them with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Indianapolis, IN
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Heating element broke
First turn circuit breaker off. Remove two retaining screws, disconnect two connectors at the end of the element, toss old element and reverse the procedure
to install.
to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Mayfield, NY
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The broiler element burned out in the oven.
As with all of my orders from Part Select the part was as correct and arrived in a timely manner. The installation was easy. Remove two screws, unplug the old element from the wires, install wires on new element and reinstall the element. Restored power and everything worked fine.
Thanks,
Ken Fuelleman
Thanks,
Ken Fuelleman
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from st marys, GA
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
part replacement
pull out, push in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Caren from Choctaw, OK
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted drip bowls
I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.
Was this instruction helpful to you?
Thank you for voting!