JBP66BY5AD General Electric Range - Instructions

the hardest part about this install was removing the glass from the channels. it seemed someone at the factory thought it would be a good idea to glue the panel into the receiver channels. they were wrong. it's supposed to be a floating panel. all you need to do is remove the entire door by lifting it at a slight angle off of its carrier arms. shake out and vacuum any loose glass, but please be careful. just because it's supposed to be safety glass doesn't mean it won't still cut you. take a straight blade screw driver and dislodge any stubborn remnants from the channels. completely remove the bottom channel. with your door in an upside down position, insert the replacement panel into the top channel, making sure you have it facing in the right direction and that the window lines up with the door window. place the lower channel on the exposed end of the panel. make sure both channels completely receive the panel. center the panel in the opening and carefully replace the screws in the lower channel. do not over tighten. turn your door right side up and re-install on the carrier arms. nice job. you just saved yourself a ton of cash. took me all of ten minutes. shouldn't take you a whole lot longer.

Ever the optimist, I'd replaced the burner on this relic of another time to no effect. That left the switch. You guys should know that when a burner element goes bad it can take out the switch. I should have put a meter on it. Wehn I looked for a replacement a few months ago there were still factory parts available, but they were $80 or so and I wasn't inclined to risk that on a 40 year old range. I offered to replace the raange for my daughter as a Christmas present but she like this old thing. It was an unusual size with a pan storage compartment on the left. I went on line and found this universal replacement for about $25 delivered. What the heck. I ordered it and it arrived within a week. I pulled the stove out, killed the breaker, pulled the knob off, used a nut driver to take ther rear panel off, two phillips screws under the knob hold the switch in. The terminals on the old switch are in a slightly different order but are clearly marked L1, L2, H1, H2 and P. The P is the power and has a smaller terminal so you can't put it on the wrong one. Just examine the old switch ( it was marked the same way) take off the L1 and put in on the L1 of the new switch and so on, make sure you use the correct knob adapter to fit your old knob and break the switch stem to the correct length. It will break easilly if you hold it with one pliers and break it with another. Screw the new switch in place with he old screws. At this point, I closed the breakers and tested it. It worked fine. I turned the breakers off again. Buttoned it up and slid the stove back into place. 20 minutes tops. Great product. Good for another forty years.

I was very impressed how quickly the package arrived. I would you your company again. I found you with a google search.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

I did not know what kind of tool was needed to remove the screws so I asked at the hardware store. When i said the screw was star shaped, he sold me torque wrench with multiple heads. First I removed the screw holding the broken handle in place. I cleaned surfaces. Next I attempted to put the handle in place on the horizontal bar and then put the screw into the opening. That did not work. I jiggled the handle for a while but could not get the pegs into the holes. Finally, I just held the handle in place and began to turn the screw and the handle slid into place as the screw got tighter.

pulled my range out and cleaned the sides!!removed the screws...pulled out the element....re-connected the wires and reattached the element...HEY it actually Worked...I installed it during commercials!and I am 75!!everything was great and you delivered it by UPS in 2 days!

part arrived very quickly. removed the rear cover. removed the old control unit. installed the new(retro fit) unit using the supplied wiring sheet diagram. The whole operation took about 30 minutes. Works great. Thanks PartSelect.

Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]

The first thing was to watch U-Tube . The replacement burner was being
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years

The initial symptom involved the heating elements turning off and on rapidly once high temperatures were reached. After cycling power to the range this went away for a few weeks. When the symptom reappeared, it involved the oven-on light turning on and off, even when the oven control was in the off position. This persisted after a power-cycle so I decided to replace the control board. The actual repair was quite easy. The hardest part was removing the sheet with the button labels from the old unit (I ended up inserting a knife and twisting it to separate the adhesive, which is only around the edges) and fixing it to the new unit in the proper position. The latter would have been much easier if I had realized up front that there are handy guide ridges against which to align it! Like another person whose repair story I read, the existing wire colors were not all an exact match. However each connector's function was clearly labeled on the PCB of the old board, so I had no trouble matching them up (line voltage was red, not black, and broil was blue, not purple). The only other difficulty I encountered was that the old yellow bake wire had a plastic guard on the connector and this did not fit in the appropriate hole on the new unit. I merely pried the guard off with a small screwdriver and used the bare spade-connector, which fit in the hole nicely. There was a small amount of exposed wire left, so i wrapped it in electrical tape although I doubt that was necessary.

1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.

New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!

Replace part an wires

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

I removed the back to gain access to the control board. Then I unplugged each wire on the old control and plugged it in on the new control - one at a time. Then removed the old control, removed the face from the old control and put it on the new one. Next I installed the new control and replaced the back. Job completed - oven works great.