Models > JMP31WA2WW > Instructions

JMP31WA2WW General Electric Range - Instructions

Jump to:

All Instructions for the JMP31WA2WW

Customer:: John from Sandstone, MN
Parts Used:: WB21X5301
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Socket set

uneven heating of oven

This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!

Was this instruction helpful to you?

Customer:: charles from ft.pierce, FL
Parts Used:: WB31T10011, WB31T10010
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Rusted out burnner bolws

Remove old burnner bolws and install new ones

Was this instruction helpful to you?

Customer:: Richard from Bainbridge, NY
Parts Used:: WB31T10011, WB31T10010
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

dirty bowls

used my hands to remove heating element, then remove drip bowls, then install new bowls, then install heating elements, done!!!!!

Was this instruction helpful to you?

Customer:: Thomas from Montgomery,, AL
Parts Used:: WB30M1
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

welded supports for the surface elements were broken

unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.

Was this instruction helpful to you?

Customer:: Sunny from Salt Lake City, UT
Parts Used:: WB31T10011, WB31T10010
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

stained drip bowls

unplugged burners replaced drip bowls plugged in burners

Was this instruction helpful to you?

Customer:: Patricia from Centereach, NY
Parts Used:: WB31T10011, WB31T10010
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

needed new drip bowls for stovetop GE

removed the burners and dropped the drip bowls in. Very easy to do,

Was this instruction helpful to you?

Customer:: Betty from Fayetteville, WV
Parts Used:: WB30M1
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

the center of the element had broken

just pulled the old one out and replaced with new one. very easy

Was this instruction helpful to you?

Customer:: Gloria from Dallas, TX
Parts Used:: WB31T10011
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Needed to replace drip bowls

Husband just snapped in place in about 8 seconds! Thanks for the fast delivery and pleasant staff assistant.

Was this instruction helpful to you?

Customer:: George from Fairport, NY
Parts Used:: WB44K5009
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

Broiler element would not heat

After turning off power, I removed the two screws and pulled the element and wires out, removed the wires and then attached them to the new element and replaced the screws. However, this did NOT correct the problem. The broiler did not work until I tried several times turning it on and off. It then worked once but then did not. It worked once more after several tries. I then called a repairman suspecting the control board. He confirmed this and tested the old element which was in good working order after all. A new board has been ordered.

Was this instruction helpful to you?

Customer:: Mike from Davisburg, MI
Parts Used:: WB44K5009
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

Replace Broiler Element

The whole job took about 20 min. TURN POWER OFF AT CIRCUIT BREAKER!! Remove 4 screws from the convection cover, then 2 more holding in the broiler element, disconnect 2 wires, and connect to the new one. put the screws back in, the cover back on the convection element and you are done!

Was this instruction helpful to you?

Customer:: Don from Los Altos, CA
Parts Used:: WB44K5009
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers, Socket set

Oven broiler stopped working. Had to replace the broiler element.

Just like the other responses described with two additional steps: 1) with a convection oven you have to remove the fan cover. It has four screws, the same size as the broiler element screws....but, get a piece of stiff cardboard the same width as the oven; put it all the way back, under the fan cover. There are holes in the oven bottom and your screws really want to roll into those holes and disappear; the cardboard will cover the holes. 2) as soon as you disconnect the element from the electrical wires....put a twist tie or other clamp on each wire as they want to fall back in behind the oven and you'll end up having to remove the build oven to get at the wires. The twist tie should keep them from falling out of reach.

Was this instruction helpful to you?

Customer:: Jess from Edmond, OK
Parts Used:: WB44K5009
Difficulty Level:: Very Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

Broiler element

I tried to unplug old element without success. Called appliance repair man and he pulled part way out, took hold of place where plugged in with pliers and unplugged. While holding back part of plug he plugged in new element--$60.00 later.

Was this instruction helpful to you?

Customer:: Lelia from Vienna, VA
Parts Used:: WB17X210
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Burner was unreliable...would stop working...I had already replaced the burner

I did as the video suggested.....I cut the old wires and spliced new ones already attached to the new terminal block. It would have been nice to have some instructions with the parts as I expected one piece but had to connect the wires to the new block and the new metal cover. I was guessing a bit. Also, I needed to use the holder strip off my old part so that it displaced the new part back far enough to insert the burner connections. That meant finding a screw and nut small enough to allow the metal cover to fit on the block. But the burner works great. I've learned that any repair requires some ingenuity.

Was this instruction helpful to you?

Customer:: John from Belle Plaine, MN
Parts Used:: WB64K5051
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Pliers

Burn box had rusted through under one burner.

With a nut driver removed the four heating element sockets (four small sheet metal screws) and the seventeen sheet metal screws that secured the burn box, removed the sheet metal box and inserted the new one. Not all the holes lined up at first for the screws, but starting in front with the four that did fit, the sheet metal gradually lined itself up with all the other holes for a perfect fit.

Was this instruction helpful to you?

Customer:: Les from Coal Creek, CO
Parts Used:: WB21X5301
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers, Socket set

The range kept giving an F2 alarm

When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.

Was this instruction helpful to you?

All Instructions for the JMP31WA2WW