JGSP48BH2BB General Electric Range - Instructions

This went pretty smoothly. Watch the video and just follow along step-by-step and it goes well. It would have only taken about 30-45 minutes (even being careful and slow) but I ended up placing the glass twice (be very careful and triple check that all the insulation gets poked under the housing and none is sticking out). The first time I had a small piece sticking out. (Use gloves for this part so your hands don't itch). The second time I needed to redo part of it is I forgot one of the spacers on the door handle and had to get that in there so the handle worked properly. I also took the time to clean the oven while the door was off so that took some time. Total I probably had 1.5-2 hours into this project but at least half of that was me cleaning and being fussy. This is an easy repair. I'm not a confident repair person and this wasn't difficult. It was a little time consuming but well worth the cost vs calling a repair person or buying a new appliance. You do need to have a specialty star head on a screwdriver but my simple tool kit had all the tools I needed. The oven has been working great since the repair.

Replaced new light housing.
Thanks to you guys for the prompt response

Flip toggles to release the oven door. Pull up on oven door to remove. Put door aside. Lift enamel bottom. Slide strait out. Remove aluminum shielding from around the igniter. Loosen igniter, unplug the igniter. Remove burner cowling. Plug in new igniter. Attach cowling to new igniter. Screw it all back in place. Stuff wiring connected back through the protective hole. Depress close door button and test. It takes about 10-15 seconds to ignite. Reinstall aluminum protector. Re install bottom enamel piece. Carfully slide oven door back on pegs and flip toggles to lock. Have a big glass of water and yell, Honey I fixed the oven!!

Removed top grate. Removed burner head . replaced with new burner head. Replaced grate.Very simple replacement. Old burner head was warped with age.

Easy

I had to drill the hole to a larger size to enable the foot to fit.

there were no grate pads so it was easy to add them.

open the oven door (remove) ,disassemble the igniter ,replace the igniter .

As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!

Nothing technical.

Used scribe to remove grate foot plug still in grate inserted new foot.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

I replaced the regulator because it would close off when not in use. The regulator would not allow gas to flow for 15-45 seconds after 1 or more valves were opened. Everything functioned fine after the gas started flowing, but after a few minutes of having all burners off, you would have to wait for the regulator to open up when you needed to cook again. It was not the biggest problem in the world, but my wife complained like it was. The fix was easy and not to expensive, especially when you consider how much she was willing to pay the repair man. Hands on work was about 10 minutes. Gathering tools and teaching my son what I was doing took up the bulk of the time.

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.