JBP90GS1 General Electric Range - Instructions

Our element blew in our oven, we took it out and saw what we needed. It was very easy to see what part we needed to order because of the great pictures on the website. The larger views really helped. We got the part quickly and put it in. It was a breeze and now our oven is working great! The best part however, is it only cost about $33.00 including shipping and handling. Much cheaper than if we would have had someone come in to fix it!

First, shut off the breaker to the stove. Removed old element by unscrewing the two screws on the plate where the element attached at the bottom of the inside of the oven. The old element was corroded at the connection, so disconnect it, attached the new one, pushed it back in the insulated socket then reattached the two screws on the plate. Flipped the breaker back on. Works great. Only took about 25 min. from start to finish.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

shut off electricity to the range, removed the screws holding the element in place, pulled the element out as far as it would go, removed the screws holding the wires in place, tossed the old element, attached the wires to the new element, pushed the element back into place and reattached the screws holding the element in place. Turned the electricity back on and the oven heated right up.

Also, the part arrived the day after I ordered it. Great Price & Great Service.

Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]

Note: Please make sure power is off!!! Turn off at the fuse panel,Main. Test oven after you turn off breaker...try turning on oven with normal switch, indicator light should be off. Also check interior light, usually wired 110 volts, may be on a separate circuit, just for safety!!. Remove retaing screws, scewdriver will work , but a nut driver is easier. Pull old element out gently and check between terminals with volt meter. Remove screws on element holding feed wire, reverse this process to install. Test oven for proper operation after installation...make sure oven cycles through a set temperature range.

A replacement Meat Probe did not correct the problem. Next replaced the Meat Probe Jack which corrected the problem. 1) To replace the Probe jack use 1/2" wrench to remove the nut and washer holding probe to a bracket on the top part of oven, just inside the oven door.
2) Unscrew two screws under the lip of the top burners, raise up the whole top, using a short stick to hold-up the top while you access the Probe Jack.
3) With your fingers gently follow 2-braded jack wires laying ontop of the insulation batting. The 2 wires run under the batting to the loose Jack. Carfully remove the old probe jack and install the new jack and secure with 1/2" wrench.
4. Pull stove out so you can get behind, unplug the stove and remove metal paneling covering back of control Panel. Locate the two braded wires running from front of oven over batting to a whole in rear oven wall, just below control panel. Replace new wires from the new meat probe jack, following the same route to back of stove. Carefully pull wires back and trace location to back of control panel. Unplug the old jack and replace the new wires, being careful not kink or fray the new wires. Replace back panel and plug in stove, lower and secure the 2 screws holding the burner top down. Check Probe on front of stove to make sure your getting a probe reading. Your done in a few minutes.

Easiest thing I've done. Shut off breaker. Unplug range. Pull out from wall (because this is a good time to remove the back, clean under and around the unit, check out the insulation and electrical contacts....or skip it, whatever). Open oven. Remove door (while ajar, pull up). Remove racks. Unscrew mounting plate from back interior wall. Set screws aside. Gently pull element forward until the leads and wires come through the insulation. Remove any strands of insulation that stuck to the leads and connectors. Unscrew leads. Keep left wire to the left and right wire to the right. DO NOT CROSS. Set screws aside. Discard old element. (This is a good time to clean your oven, if you haven't in a while.) If you cleaned oven, wait until dry. Position new element, feet down, in bottom of oven. Position left wire on left connector. Screw tightly BUT DO NOT BEND LEAD. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Position right wire on right connector. Screw tightly BUT DO NOT BEND. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Do not leave screws loose. Connection must be tight. Fire hazard, otherwise. If you bent nothing, then gently push element back through insulation until mounting plate is flush. Screw into position. Replace racks. Replace door. If you decide to check insulation and other leads, now is the time. I checked mine and it's a good thing I did.... Unscrew back plate of oven, keeping screws in order. Remove plate. Check that your new element and insulation aren't bunched up or otherwise in a hazardous state. You may notice burned or greasy insulation. You may see burned leads on light receptacle and broil element. If you do, then replace them, too. When finished with everything, replace back plate. Put range back into position, ensuring level and plumb. Plug in. Turn on breaker. Pat yourself on the back. You just saved $100-$250, depending on where you live.

I removed the oven door by unlocking the hinges and pulling out. Set on workbench (with towel/pad) and removed handle, four screws, then bottom and inside panel screws, then one nut to finally be able to get at the inner glass insert. Removed insulation and then took an extra hour to really clean all surfaces (middle glass was quite greasy due to inner glass being broken for a while. Reassembly wasn't bad, but took a while to figure out that the two thin 2" red spacers belonged around the two handle screws. This was tough to figure out as they come off when taking the handle off, but you can't see them, so didn't know where they came from! Anyway, if you're just a bit handy, you can do this job.

1. Make sure electricity is off!
2. Remove 2 screws at rear of oven where the bake element is attached.
3. Pull out far enough to remove the 2 screws where the wires attach.
4. Lift out the old element and set the new one in.
5. Reattach the wires.
6. Reattach the element to the rear of the stove.
7. Turn electricity back on.

1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.

New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!

Replace part an wires

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.