JBP67CM2WW General Electric Range - Instructions

Pull the old one put in the new one ... took about 20 minutes

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

The repair took Less than 20 Mins. So easy anyone that is handy should be able to do this with ease. And PartSelect is great to order from Order was placed on a Weekend and order was at my home on Tues! Thats a one day shipping and it was a ground shipment!!! Great Job PartSelect!!!!!! Mark

Tried GE onoine parts department first and ordered the wrong part, then tried the customer hotline and they referred me to the right part but didn't explain that the design had been modified (the drawings had not been updated). I found an explanation on Part Select AND the parts were cheaper. Part Select sent the part, the necessary screw, and an appropriate instruction manual. Each support took less than a minute to screw in with a socket wrench.

Some of the original TO-9 switches were fused by the heat. I made them functional again with a cutter on a rotary tool, but to make the repair properly, I ordered the new control unit and the faceplate graphics. Note the guide tabs at the bottom and right edges when replacing the graphics. Don't plan on reusing your old graphics (unless you are a wizard at removing the very strong adhesive).
To gain access to the part, remove the 2 screws (part 715) in the bottom of the control assembly with a stubby screwdriver. Using a nut driver, remove the two screws (part 1000) on the back at the corners, being careful not to drop them behind the oven. Pull out at the bottom, then move the whole unit toward you. Note the position of the wires. A digital photo can help here. Remove the wiring and 4 screws holding the clear plastic TO-9. Put the screws in the new unit in the same holes and rewire. Put the assembly in place top-first and align the screw holes. Finding the same thread placement for the lower screws can be tricky, so start them gently.

When we moved into our new home I discovered that the oven that came with the home did not have any racks in it. I ordered these racks because they said they were compatible with Hotpoint ovens. However, when the racks arrived they were just a tad too wide to easily slide in the oven. With a bit of force my husband was able to shove the racks in. Luckily I don't cook enough to care if they are moved again because I don't think they'll come out easily.

First I shut off power to the unit. Then I removed the oven shelves. Next, I removed the two screws that hold the element in place using a socket ratchet. Then I carefully pulled the element out a few inches. I had some clothes pins with me because I read how some people had problems with the wire leads slipping back into the unit insulation. When the terminals and wire leads were exposed, I clamped the clothes pins on the wires between the leads and the oven wall so the wires could not be pulled back into the wall. Then I disconnected the wires from the old element. Next, I connected the new element to the wires, removed the clothes pins and gently nudge the element terminals back into the oven wall. Then I put the screws back to secure the element. Finally, I turn the power on and set the oven to 400 degrees. When I saw the element get red hot in a couple of minutes, I knew it was fixed. I've used it several times since then.

Used a pliers to remove old bake element (2 nuts that none of our socket set would fit). Removed the back panel with screwdriver. Unattached bake element from wires. Then removed old element and put new element in, pulled new element wires through back and reattached to range. Screwed back in the oven with the pliers. Closed up the back panel with the screws.

1. Pulled the stove out about 6-8 inches. 2. Opened oven door and removed 2 screws to free up stove top. 3. Lifted stove top to access another panel. 4. Removed about 6 screws allowing removal of sheet metal cover above Latch/lever mechanism. 5. Removed 2 screws at top center "boiler plate" to allow removal of Latch/Lever mechanism. 6. Slipped off electrical connector from microswitch mounted on Latch/Lever mechanism. 7. Then removed old mechanism 8. Set new mechanism in place, re-attaching electrical connector onto microswitch. 9. Then with my finger, I bored down a few inches through the insulation to make sure the base of the new Latch/Lever mechanism was in contact with the oven at the base of the insulation. 10. I replaced the 2 screws at the top center "boiler plate." 11. I reattached the sheet metal cover with 6 screws, making sure holes were lining up. 12. Finally, I lowered the stove top and reattached the remaining 2 screws that secure the stove top. It was all pretty easy, but I did not see a prop (like some models have) that would hold up the stove top while performing the unscrewing, screwing, removing, replacing, etc., so I used a piece of wood to rest the stove top on, and lifted it with my left hand while I did the "operation" with my right hand.

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...

Turn off power to oven,remove two screws holding element in place,pull element forward approx. 1" and unplug wires,remove element. Install new element in reverse order of above.

I unplugged the stove then took the oven racks out. Then I took a nutdriver and took out the 2 screws that held the Bake Element in place. Pulled the 2 prong's out of the oven and removed the wires from the tips. They pulled right off.
Took out the new Bake Element and reversed the process. Attached the 2 wires put the 2 prong's back into the holes and screwed the 2 holding screws back in. Plugged the Stove back in and turned her on. Doing it myself saved me $150.00.

Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.

After reading all the repair stories I knew that their wasn't any extra wire when the old element is removed. Well, even with that knowlage one of the wires came loose and slipped back in. Fortunately I was able to remove a panel in back and push it back through. I was afraid I would have to take off the whole back but instead there is a panel covering the wire running down the center of the oven. After removing 5 screws with the same nut driver as the one for the coils I had it done in minutes. I had no problem and I am NOT a 'do it yourselfer'. Oh, did I mention I ordered the part on Friday and received it on Saturday standard shipping? Pays to live the next state over from the place shipping it.

loosen interior panel of oven with star driver. Removed broken arm. install inner screw and then install final screw to both panels and handle.

The inner screw mount only through the exterior door only making it tricky to line up the final bolt which goes through both panels and the handle.

Other than that it when smoothly.