PGS908BEM1BB General Electric Range - Instructions

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

Easy to install replacement parts using the screws provided.

Replaced all four

This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.

Owners manual provided no help. Thankfully, the internet did. Internet convinced me the problem was the igniter, and with hindsight that was correct. 30 mins on the net to troubleshoot. On my model, the oven door must be removed to remove the bottom splash shield. Internet to the rescue to show how to remove the oven door. 10 minutes on the 'net, 30 seconds to remove door. Heat shield came out in about a minute. First machine screw that secures the igniter to mounting bracket out in 45 seconds. Second machine screw stripped in two wrench turns. Since the location of the mounting bracket was a cramped space (in a "well"), had to hand hold a hacksaw blade to cut off the head of the stripped machine screw. With only 3/4" of possible travel, this took 90 minutes. Then drill out the remaining shaft of the stripped fastener. The new igniter went in no problem and I used sheet metal screws to reaffix the unit. From what I've seen on the 'net, cheap fasteners that strip is a common fault on GE appliances.

I had read the customers reviews and expected that I'd most likely break the attaching screws. My trick was to not just unscrew then all the way out but to turn it a half a turn and then screw it back in. Then out again a little more then last time and back a little. Didn't break a thing. I did have to move the stove out to get to the plug but that was just enough for me to get my arms in there.

Odered igniter from part select, it arrived the next day. Removed oven door removed heat shield on bottom of oven and there it was. Removed the two screws pulled the wires till the connector came through, unpluged connector, plugged in new igniter, repaced everything and Bam, we were cooking. Did not even have to pull oven out from the wall. Super easy.

No response from GE website (very disappointing). google "repair GE gas range igniter" and very simple step-by-step instructions...apparently is very common with GE appliances...even mine that was less than 14 months old. Service tech would have charged $300. Did it myself for $80

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.

Lifted both pieces off and placed the new ones on,turned on the burner and it worked as it should.

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!