JB900BK6BB General Electric Range - Instructions

So easy. Took extra time so the wife would think it was harder. Just read the other reviews for instructions. Didn't have an issue with the wires pulling back into the oven though I did have my "clips" ready.

popped the new one on!

Easy

Really easy even i could do it , it was a little fiddly and the wires disappeared into the back of the oven , i easily removed the rear panel and pushed the wires back thru and connected them , turned the breaker back on and sparks !!
removed the rear panel again in 2 mins and saw that the wires were touching the oven frame and had shorted out , it wasnt a problem moved them slightly, reconnected them to the element tightened them up , put breaker on and Done , took about 45 mins but i could of been done in 30 with a little more care in the beginning of the job EASY !

I removed the racks and oven door. I used a socket to remove the screws that secured the element. I pulled the element out to gain access to the wire connectors and used pliers to remove the wires from their connectors to the burned out element. I installed the new element by using the pliers to secure the wire connectors to the element and then installed the element with the socket thus securing the element with the screws.

First I unplugged the stove. Then I removed the two screws inside the oven to remove the heating element. For safety purposes I removed the back panel from the stove also to get a complete view of what I was getting into. That was just 5 more screws and the panel came off and exposed what the heating element was plugged into. Very easy to unplug and reconnect, install the back panel then install the two screws for the heating element and it works just fine.

First, my husband removed the two screws that hold in the element. Unfortunately, my GE Spectra oven had extremely short wires. That was the only thing that made it somewhat difficult. So, he pulled the element out as far as he safely could, replaced it with the new one. No problem! As I said, the only thing that made it difficult was the short wires supplied by GE. The part came from PartSelect.com with no problems. I would definitely use this website again to order parts.

I turned the breaker off to the stove and moved it away from the wall. I then removed the center cover off the back of the stove and exposed the wires connected to the bake element. I removed the wires from the bake element and then opened the oven and removed the two bolts holding the element onto the back wall of the oven. I discarded the old element and replaced it with the new first bolting the new in , then connected the two wires and replaced the rear cover. Turned on the power and made a cake.

First unplug the unit from the outlet. Then remove the rear cover, covering the electrical wires. Disconnect the hot /ground wires from the element leads. Then open the oven door and use the nut driver to remove the inner screws to release the bake element. Insert new element and replace all screws and electrical leads. You're all done!

We decided to go "on line" to see if there was any way to fix the stove ourselves and found the Part Select website. After entering the model number for the stove, we were able to find the heating element. We ordered it and received it two days later! We saved money and time. Thank you!

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

First of all i ordered the part and recieved it the following day, thank you PartSelect. :) Installation was a breeze. I just turned off the main circuit breaker then pulled the range out from its position between the countertops. I used an adjustable wrench to remove two small bolts holding the baking element in place, carefully pulled out the element to expose the two wires, disconnected them and connected the new element, put the backplate bolts back in turned on the main breaker and the oven worked as good as new.

Took two screws out, unplugged the wires.

Put the new heating element in. Plugged in the wires and put the screws back.

Took about 16 minutes !

First my husband removed the two screws that hold the element in place. Then pulled the element out and diconnected the two wires. The wires popped back in, so he took the shield off the back, I pushed the element in so he could see the prongs and hooked the wired back on. He then replaced the 2 screws and i was back to baking.
Thanks

Removed 2 hex head machine screws. Picked up on the element and slid wires through. One wire became unattached. Removed back panel, pushed wire through the oven wall, and replaced the back panel. Wires connected with push on connectors. Pushed attachment assembly back through the oven wall and replaced 2 machine screws. Viola! Working oven.