JKC26104 General Electric Range - Instructions

The bake element in my 17 year old GE free standing electric range became defective. This element has 2 terminals -- black (240V) and white (neutral). While removing the element from the range, a 2nd black wire was pulled out of the back of the oven. This wire had a bare terminal connection and apparently had been loose behind the oven shell for all these 17 years. Inspection of this wire showed it carried 115V. I wrapped this wire with electrical tape and reinserted it into the insulation behind the oven shell.

The hardest part was working in the oven.

Turn off power
Open Oven Door, remove racks
Remove two mounting screws with nut driver.
Slide the element out to expose the wire connections.
Remove the screws and pull the element out.
Place the new element in oven.
Clamp on to each of the terminals with vice grips to keep from bending the element and install the screws.
Slide the element back into place and put the two mounting screws back in.

Put the racks back in and turn on the power and test. You may get a little smoke off the new coil.

Like I said the hardest part is leaning into the oven to attach the screws, do not sit on the oven door.

With great ease. Only thing I would have appreciated was knowing the size ofvthevrequired socket wrench. Otherwise it was easy and fun as the instructions were crystal clear.

unplugged oven. removed oven racks.Disconnected old unit. Installed new unit. Very very simple

No. 1 thing I did is I unplugged power supply to oven, second- unscrewed two screws that was holding cover plate and removed cover plate with a set of pliers, pulled element out and unscrewed two screw with power wires and installed new element, tightened screws and re-installed cover plate, tested oven turning on oven and in a few seconds element got hot, job done!

First I turned off the breaker to the oven,
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the oven on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

My daughter and I turned off the breaker to the range and removed the old element and replaced it with the new one. My husband came home and took over after we had done almost everything ourselves!!

Unpluged Stove, Unscrewed the wires attached to the Element in the back of stove after I removed the cover. Removed the two screws that held the Element at the back of the oven compartment. Then replaced the Element with the new one and put back the screws, the wires and the cover in the same sequence iI took it apart. Plugged it back in works like new!

My husband removed the screws holding the element, disconnected the wires from the old element. He then reattached the wires to the new element, putting it back into place, tightened the screws, and we were cooking again. The shipping service was GREAT! I ordered the part on-line and it arrived next day! Thanks!

I removed the original element with socket set (two hex nuts). I removed the element and face plate, reversing the steps when installing the new element. It was simple.

The bake element is very easy to replace. Turn off the circuit breaker to the stove. Two screws (1/4" socket needed, not screwdriver) come out to release the plate, then two more screws of the same size to unfasten the element to the stove wiring. Reverse the process to put the new one back in. I let my fourteen year old son do the whole thing. By the way, the photo of the element on the web site did not look like the element in my stove. I called customer support and was assured that it was the proper part. When it arrived, it did exactly match my element. The photo on the web site was incorrect. (Part number PS249466)

Unplugged oven. Removed the two screws from inside the oven that secured element to the back. I then removed the protective cover for the plug from behind the oven-three screws. Disconnected the element from the electrical wires, removed and replaced the element. And reassembled the cover and all the screws in reverse order. Plugged it in. Presto, 5 mins and works great.

I noticed two screws held the heating element in place. I removed the screws. Pulled the heating element out a few inches. Removed the two additional screws which held the two wires on.

To install the new element, I used the two new screws that came with the element to attach the wires to the element. Insert the element into position and attached the element to the rear wall with the two screws which were first removed.

turned off the electric at the breaker box.
removed the door, and racks. unscrewed two bolts, pulled out and unscrewed the leads. reattached the leads, and pushed in and reattached the element.
put the racks and door back on. turned on the electric and then tested the oven. easy!!