JKC26104 General Electric Range - Instructions

remove screws attaching burner plate to back of oven, pull out element, undo wiring to old burner by unscrewing 2 screws, remove old burner, reverse process to put new burner in

Removed 4 screw nuts and replaced with new baking element using same 4 screw nuts. Real easy job.

First I turned the power off to the oven/stove at the breaker box in the basement. Then I took the back plate off. Then I removed the two screws holding the wires onto the damaged element. Then I removed the two screws holding the element to the inside rear of the oven. Then I pulled the old element out and replaced it with the new element. I replaced the two screws that hold the element to the inside of the oven. Then I replaced the wires on the element where it protruded at the back of the oven. I put the back plate back on, slide the oven back in place and turned the power back on at the breaker and everything worked.

First shut off power to the range in the electrical
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)

Unplugged range. Removed old element from back of oven which was held in by two screws. Unscrewed the wires that were attached to old element and screwed them into the new one.

I first removed the two hex head screws, pulled the element slowly forward about four to five inches and disconected the two wires on the old element.
I removed the old element and attached the wires to the new element. I then slowly pushed it back into the rear wall of the oven, carefull not to disturb the insulation around the opening and replaced the two screws that hold the element to the back wall of the oven. It was easy enough to do, even for a woman. I turned on the oven and it worked great. No problems so far.

Had to take back panel off of the inside of the oven to get to the screws to remove the old element and attache the new. Removed the two screws to remove the old, pulled it out unattached the wires and attached the new one.

Turned off power. Removed oven racks. Removed the 2 screws that held the element in place. Pulled element out about 3 in. & disconnected 3 wires. Placed new element, reconnected 3 wires & reconnected the 2 screws that hold element in place. Turned power back on & it works great!!. Was very pleased at how easy it was & also how fast I received the part, which was day after I ordered it.

I removed the old element and replaced it with a new part. It was very simple.

The power was turned off. The elemnt wiring was removed. The new one was installed in reverse order. Power back on and the oven tested just fine.

First shut off power to the store and used a socket set to remove 2 screws and disconnnect the element. Connected the new element but had to use the old screws as the new ones did not work with my appliance.

Could not believe how fast the part shipped. 2 days and it was here. All it took was using a nut driver to remove 4 screws and then put the new one in.

With great ease. Only thing I would have appreciated was knowing the size ofvthevrequired socket wrench. Otherwise it was easy and fun as the instructions were crystal clear.

No. 1 thing I did is I unplugged power supply to oven, second- unscrewed two screws that was holding cover plate and removed cover plate with a set of pliers, pulled element out and unscrewed two screw with power wires and installed new element, tightened screws and re-installed cover plate, tested oven turning on oven and in a few seconds element got hot, job done!

First I turned off the breaker to the oven,
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the oven on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.

My 17 year old son and I (his mom) replaced the oven element in less than 15 minutes!!! It was so easy. We first unplugged the stove since I didn't want to go and shut off the circuit breaker in the dark!! We then removed the two screws that hold the element in place and started to pulled out the element. It was actually corroding in my hands as I pulled it out. We disconnected the wires and then put in the new element by reconnecting the wires, pushing the connections back in and replacing the two screws that hold the element in. The oven heated right up!!! What a savings to do it yourself and not have a repairman charge us extra to do a 10 minute job!! Thank you Part Select for your fast service. I will definitely look here before I shop anywhere else. Thanks,