JM250DF4WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- HAROLD from Tucson, AZ
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Just follow the enclosed instructions
Followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CASPER, WY
- Parts Used:
- WB21X5301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad sensor
By myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ron from reston, VA
- Parts Used:
- WB44X48671
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The bake element in the upper oven broke
I counldn't get the nut screw out. It wounldn't turn. Had to call a technican.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen M from Nampa, ID
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner didn't work, using a test light showed only one side was hot.
took the back panel off the range, took the 2 screws holding the switch in place, took the old switch out, marked the wires took the wires off and clipped them onto the new switch, put the new switch into the switch plate, replaced the screws put on the knob, put the panel back on the range. rolled the range back into it's place. turned the buner on to check if it worked. It did so we were done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Mead, CO
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced my drip pans
The new drip pans are great. I had purchased generic ones locally that were supposed to be universal. The problem was that they did not fit right and the burner coils did not sit flat. The new drip pans fit well and look great too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Alpena, MI
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I ord. drip pans for my Mother in another state
The drip pans arrived and she switched them out with the old ones Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Ellenboro, NC
- Parts Used:
- WB24T10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The 8" burner switch heated burner to high Temp
Went online looked up model no and found Part No. and ordered it couple of days It came in mail Cut power to oven took knob off two screws back panel. wired new switch like the old one replced thwe switch and two screws and panel connected the power tried new switch it worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bainbridge, NY
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dirty bowls
used my hands to remove heating element, then remove drip bowls, then install new bowls, then install heating elements, done!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felipe from Donna, TX
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The burner combusted burning the the burner switch
Disconnected the appliacnce from the power source. Using screwdriver, removed the back panel and disconnected every wire that are connected to the switch. Pulled out the front nob and removed the switch. Then install the new switch by screwing it back in. Place all wires back and back panel. Connect and finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Constance L from Woodhull, NY
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Disgusting looking burner drip bowls.
Just had to change out the drip bowls, easy. But, I wanted to comment on the quick delivery on the new bowls. I was impressed. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie N from Carson City, NV
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
none
Took the old pans out and put the new ones in. Simple as pie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from De Leon, TX
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Front and back burners not getting hot
Followed the video supplied with the email on the parts order form. Biggest problem was pulling the range out from the wall, the repairs went without a hitch. The PartsSelect video was a great help showing the short cut to getting the new wires in by using the old wires as a pull wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Winter Garden, FL
- Parts Used:
- WB24T10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner would not turn off
The burner light did not turn off, and the rear burner stayed hot. Unplugged unit and removed switch, which turned off the "burner lit" lamp. Thus I figured it was the switch that was causing the problem. Ordered the switch (I think around $18 and plugged it in. I think there were 4 screws to get the panel off, and then another 2 to get the switch off. When I plugged the unit back in (it had been unplugged while I waited for the part to ship) it beeped for a while. I had to turn the breaker on and off, and that solved the beeping problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from norwalk, CT
- Parts Used:
- WB17T10006, WB31T10011, WB31T10010, WB24T10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
burner switch needed replacing
replaced wire for wire
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fuad from Sarsota, FL
- Parts Used:
- WB17T10006
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
2 mounting bracket included, wires too long
I couldn't tell which one work best till I installed 2 units and I liked the other bracket for stability.The wired were too long and there is not a given way to strap them and keep them away from the heat source.
Was this instruction helpful to you?
Thank you for voting!