JM250DF4WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roy from Au Gres, MI
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Could not adjust heat on burner.
Followed directions given by previous customers problems which we found on the internet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lucille from HAPPY CAMP, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner was not heating
unplug it and plug the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from JACKSON, MO
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
control switch had stopped working, burner wouldn't work properly
took out a couple of screws and replaced with new switch, plugged in switch wires. very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from ALPENA, MI
- Parts Used:
- WB02T10037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
The light socket cup could no longer hold the bracket that holds the light cover in place.
I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Garden City, ID
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed New Burner Bowls
Removed the old burner bowls, replacing them with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from st marys, GA
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
part replacement
pull out, push in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Caren from Choctaw, OK
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted drip bowls
I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William W. from Seattle, WA
- Parts Used:
- WB24T10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Surface element switch failed
Top front sloping sheet metal panel with all controls and plastic end caps has to come off. Need 2 people, one to hold it while other replaces switch. Problem was getting screw holes on bottom ends lined up and cuts from sheet metal edges. Ten minutes to get it apart, 40 to get it back together. New switch works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bayani P. from DALY CITY, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Burnt Terminal Block
Unplug the range before opening the back panel and removed the wiring connection and replaced with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Greenwood, IN
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
electric burner shorted out and fried the switch
Removed two screws holding the housing in place and loosened two more on the back it order to free it. Switch was held i place with two screws, removed those. Transfered wires one by one on the new switch, which was identical OEM part, and replaced the screws. VERY simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from san jose, CA
- Parts Used:
- WB36X192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dropped & broke the oven light bulb cover
popped the new one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from UNION SPRINGS, NY
- Parts Used:
- WB31T10011
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drip bowls had deteriorated after years of use
Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from Tucson, AZ
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Just follow the enclosed instructions
Followed the instructions
Was this instruction helpful to you?
Thank you for voting!